Advanced, Static Routing | Billion Electric Company BIPAC-7500G

Advanced

Billion BIPAC-7500G–802.11g ADSL VPN Firewall Router with 3DES Accelerator

Advanced

Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconfigure their router, unless advised to do so by support staff.

There are four items within the Advanced section: Static Route, Dynamic DNS, Checking Email and Device Management.

Static Routing

Click on Routing Table and then choose Create Route add a routing table.

Destination: This is the destination subnet IP address.

Netmask: Subnet mask of the destination IP addresses based on above destination subnet IP.

Gateway: This is the gateway IP address to which packets are to be forwarded.

Interface: Select the interface through which packets are to be forwarded.

Cost: This is the same meaning as Hop. This should usually be left at 1.

97

Chapter 4: Configuration

Image 101

Billion Electric Company BIPAC-7500G user manual Advanced, Static Routing

Contents

802.11g ADSL VPN Firewall Router with 3DES Accelerator User’s Manual Version Release 1.10eBIPAC-7500G Page CHAPTER 2 INSTALLING THE ROUTER Table of ContentsCHAPTER 3 BASIC INSTALLATION CHAPTER 4 CONFIGURATION CONTACT INFORMATION CHAPTER 5 TROUBLESHOOTINGAPPENDIX A PRODUCT SUPPORT AND S AVE C ONFIGURATION TO F LASH Wireless Ethernet 802.11g FeaturesFast Ethernet Switch Quick Installation Wizard Network Address Translation NAT Universal Plug and Play UPnP and UPnP NAT TraversalFirewall Domain Name System DNS relay Firmware Upgradeable Dynamic Host Configuration Protocol DHCP client and serverStatic and RIP1/2 Routing Simple Network Management Protocol SNMP Figure 1.1 Application Diagram BIPAC-7500G ADSL Router Application Important note for using the BIPAC-7500G ADSL Router Chapter 2 Installing the RouterPackage Contents Meaning The Front LEDs1 PWR 2 SYS 3 LAN port 4 LAN port 5 LAN port 6 LAN port 7 WLAN 10 MAIL 11 PPP 13 ADSL The Rear Ports RESET PWR Power SwitchPort LINE CONSOLE LAN Cabling Connecting your router Chapter 3 Basic Installation For Windows XP Configuring PCs in Windows2. Double-click Local Area Connection. See Figure 4. Select Internet Protocol TCP/IP and click Properties. See Figure Double-click Local Area “LAN” Connection . See For WindowsIn the LAN Area Connection Status window, click Properties . See Figure 3. Click Properties 5. Then select the DNS Configuration tab. See FigureFor Windows 98 / ME 2. Select TCP/IP Protocol and click Properties. See For Windows NT4.03. Select the Obtain an IP address from a DHCP server Figure 3.12 TCP / IP Username and Password Factory Default SettingsLAN Device IP Settings ISP setting in WAN site PPPoE PPPoA RFC1483 Bridged RFC1483 Routed IPoA Information from your ISP Figure 3.14 User namd & Password Prompt Widonw Configuring with your Web Browser Quick Start Chapter 4 ConfigurationSave Config to FLASH ARP Table Status RIP Routing Table Routing TableRouting Table Leased Table DHCP TableExpired Table Permanent Table PPTP Status IPSec Status Email Status L2TP Status UPnP Portmap Error LoggingEvent Log Quick Start Click Start to begin scanning for encapsulation types offered by your ISP. If the scan is successful you will then be presented with a list of supported options LAN Local Area Network ConfigurationEthernet LAN, WAN, System, Firewall, VPN, QoS, Virtual Server and Advanced ESSID Broadcast Wireless WPA Pre-Shared Key Wireless SecurityPage Port Setting DHCP Server the requesting PC in the LAN your Local Area Network WAN Wide Area Network RFC 1483 Routed Connections PPPoE Connections Connection Advanced Options PPPoE discovered the DNS server IP address, it automatically gives the address to the local DNS relay so that a connection can be established All Ip Pppoe RFC 1483 Bridged Connections PPPoA Routed Connections Advanced Options PPPoA Chapter 4 Configuration IPoA Routed Connections Page ADSL Time Zone System Remote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control URL Filter To block PCs on your local network from unwanted websites General Settings Packet Filter Table 1 Pre-defined Port Filter Port Filters Address Filters Click Port Filters Configuring Packet Filter 4. Click Add TCP Filter Click DeleteClick Add TCP Filter Input HTTP port number Select “Allow” HTTP inbound & outbound application Block Duration Intrusion Detection Intrusion Name Detect Parameter Blacklist Table 2 Hacker attack types recognized by the IDSType of Block Duration Drop Packet MAC Address Filter URL Filter Restrict URL Features Log information can be seen in the Status - Event Log after enabling Firewall Log PPTP VPN Virtual Private Networks Remote Access PPTP Connection Click Apply after changing settings LAN to LAN PPTP Connection Click Apply after changing settings Click Create to configure a new IPSec VPN connection IPSec Local Configure a new VPN ConnectionRemote Proposal MD5 A one-way hashing algorithm that produces a 128−bit hash Advanced Option L2TP Remote Access L2TP Connection MD5 A one-way hashing algorithm that produces a 128−bit hash LAN to LAN L2TP Connection IPSec Enable for enhancing your LT2P VPN security Configuring PPTP VPN in the Office Example Configuring a Remote Access PPTP VPN Dial-in ConnectionFunction Description Auto stateful Key Length Mode Idle Time Configuring the PPTP VPN in the Office Example Configuring a Remote Access PPTP VPN Dial-out Connection stateful Mode Idle Time Example Configuring a LAN-to-LAN PPTP VPN Connection Configuring PPTP VPN in the Head Office Configuring PPTP VPN in the Branch Office Table 3 Network Configuration and Security Plan Example Configuring a IPSec LAN-to-LAN PPTP VPN Connection192.168.0.0/24 69.1.121.30 192.168.1.0/24 69.1.121.3 12345678 Tunnel mode ESPMD5 with AES WAN side Configuring IPSec VPN in the Head OfficeIP address of the head office router in Configuring IPSec VPN in the Branch Office QoS Quality of Service High Prioritization IP Throttling Port Number Protocol Virtual Server “Port Forwarding”Table 4 Well-know and registered Ports POP3 Post Office Protocol Version TCP or UDP, however you can specify other protocols using the drop-down Protocol menu. Setting the protocol to “all” will cause all incoming connection attempts using all protocols on all port numbers to be forwarded to the specified IP address Static Routing Advanced Dynamic DNS Check Emails Embedded Web Server Device Management SNMP Universal Plug and Play UPnPSNMP V1 and From RFC 1213 MIB-II SNMP Version SNMPv2c and SNMPv3From RFC1650 EtherLike-MIB From RFC 1493 Bridge MIB From RFC 1473 PPP/IP MIB From RFC 1472 PPP/Security MIBFrom RFC 1474 PPP/Bridge MIB From RFC1573 IfMIB Save Configuration to Flash Logout Problems starting up the router Chapter 5 TroubleshootingProblems with the WAN Interface Problem Can’t ping any PCs on the LAN Problems with the LAN InterfaceFrequent loss of ADSL linesync disconnections WORLDWIDE APPENDIX A Product Support and Contact InformationContact Billion AUSTRALIA