Part No. 890049 Form No. F 100 202A
Page 8 of 8
Before Requesting Service Review These Suggestions
20
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
22.1 22
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON LEE'S SUMMIT, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
PurchasedfromPurchaseDate
21 Serial Plate Record your machine model, serial number and
date-of-purchase and where purchased
min-1
1803 S.W. Jefferson
Lee's Summit,
MO 64062 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
R
MAINTENANCEIMPELLER REMOVAL
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove engine, impeller and mounting plate by removing nuts
(item 26) around outside of housing.
4. Leaving engine fastened to plate, remove impeller bolt (item 50)
and lock washer and slide impeller off crankshaft ( A puller may be
required). CAUTION: Do not drop impeller.
5. If impeller does not slide off crankshaft, place two crowbars
between impeller and housing on opposite sides. Pry impeller away
from engine until it loosens. Using a penetrating oil can help loosen
a stuck impeller.
6. If the impeller cannot be loosened, obtain a 1” (25.4mm) longer
bolt of the same diameter and thread type as the impeller bolt.
Invert engine and impeller and support engine above ground to
prevent recoil damage. Thread longer bolt by hand into the
crankshaft until bolt bottoms. Using a suitable gear or wheel puller
against the bolt head and the impeller back-plate (near the blades),
remove impeller from shaft.
7. To reinstall impeller, use a new impeller bolt and lockwasher
8. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N.m).
9. Reinstall engine, impeller, and mounting plate onto housing in
reverse order of removal.
10. Before connecting spark plug wire, slowly pull engine starting
rope to insure that impeller rotates freely.
11. Reinstall spark plug wire.
Use only a qualified mechanic for anyadjustments, disassembly or any kindof repair .
DISCONNECT SPARK PLUG WIRE
BEFORE SERVICING UNIT.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN
MACHINE OFF, MAKE SURE ALL MOVING PARTS COME
TO A COMPLETE STOP.
RECONNECT SPARK PLUG WIRE,
GUARDS, BAG, CAPS AND / OR
HOSE BEFORE STARTING ENGINE.
ENGINE: See engine manufactureroperator's instructions.
17.1
17
Engine (See Engine Manual)
Check for excessive vibration
Clean Debris Bag
Inspect for loose parts
Maintenance Operation
Follow these hourly
maintenance intervals.
Maintenance Schedule
Inspect for worn or damaged parts
Every 5 hrs
or (Daily)
Every
Use
17.2
For damaged or imbalanced
impeller
Problem Possible Cause Solution
Will not vac uum or has poor v acuum performance. · Dirty or full debris bag or f ilter. · Cl ean debris bag and filter. Shake bag clean or
wash.
· Nozzle height set too high or too low . · Adjust nozzle height.
· Hose kit cap missing. · Check for hose kit cap.
· Clogged nozzle or exhaust. · Unclog nozz le or exhaust (see page 5)
· Excessive quantity of debris. · Allow air to feed with debr is.
Abnormal vibration. · Loose or out of balance impeller. · Check impeller and replace if required.
· Loose engine. · Check Engine.
Engine will not start. · Throttle in off position. · Check throttle
· Engine not in full choke position. · Check throttle, choke position
· Out of gasoline or bad or old gasoline. · Check throttle, choke position and gasoline.
· Spark Plug wire disconnected. · Connect spark plug wir e.
· Gas Valve off . · Turn on gas valve.
· Dirty air cleaner. · Clean or replac e air cleaner. Contact a qualified
service perso n.
· Safety Interlock disengaged on bag plate. · Bag not fully engaged or Rod in bag is bent.

109 dB

TROUBLESHOOTING