ASSEMBLYAND ADJUSTMENT
•INSERTINGToinstall a bit,ANDinsertREMOVINGit into theBITScavity(FIGUREin the hexC)
spindle as shown in .
• Toremove the bit pullfigureit straightC out.
• For bit tips, use a bit tip extender as shown. NOTE: Only hex end bits will fit in spindle.
• DonotusescrewdriverasaWARNING:prybarinanyposition.
• Toavoid screwdriver being turned on accidentally, do not carry in your pocket.
C |
| OPERATING INSTRUCTIONS | |||||||||
| Yourscrewdriver uses gyroscopic technology to sense your hand motion. Tooperate, | |||||||||
| press in the motion control activator on the back of the tool with your palm and turn | |||||||||
| your hand in the direction that you want the screwdriver to operate. | |||||||||
SETTING INITIAL STARTING POINT |
|
|
|
|
|
|
| |||
• Grasp the screwdriver as shown in figure D. |
|
|
|
|
|
|
|
| ||
• | Press and hold in the motion control activator on the back |
| D | |||||||
| of the tool with the palm of your hand. |
|
|
|
|
|
|
|
| |
• When the LED illuminates the tool is ready for use. |
|
|
|
|
|
|
|
| ||
• | To reset initial starting point first release the motion control |
|
|
|
|
|
|
|
| |
| activator. Move tool to new position, then press and hold in |
|
|
|
|
|
|
|
| |
| the motion control activator on the back of the tool with the |
|
|
|
|
|
|
|
| |
| palm of your hand. |
|
|
|
|
|
|
|
| |
OPERATING IN FORWARD DIRECTION |
|
|
|
|
|
|
|
| ||
E | ||||||||||
• Grasp the screwdriver as shown in figure E. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||||
• Engage head of fastener with screwdriver accessory |
|
|
|
|
|
|
| |||
| on work piece. Follow instructions for setting initial |
|
|
|
|
|
|
| ||
| starting point. |
|
|
|
|
|
|
| ||
• | Rotate your hand to the right and the screwdriver will |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||||
| activate in the forward direction. |
|
|
|
|
|
|
| ||
OPERATING IN REVERSE DIRECTION |
|
|
|
| ||||||
| ||||||||||
|
| E1 | ||||||||
• Grasp the screwdriver as shown in figure E. |
|
|
|
|
|
|
|
| ||
• Engage head of fastener with screwdriver accessory |
|
|
|
|
|
|
|
| ||
| on work piece. Follow instructions for setting initial |
|
|
|
|
|
|
|
| |
| starting point. |
|
|
|
|
|
|
|
| |
• | Rotate your hand to the left and the screwdriver will |
|
|
|
|
|
|
|
| |
| activate in the reverse direction. |
|
|
|
|
|
|
|
| |
| Toturn the tool off, release the motion control activator. |
|
|
|
|
|
|
|
| |
NOTE: When the tool is not in use or during transit please be sure to remove any | ||||||||||
| accessory from the tool. |
|
|
|
|
|
|
|
•45ToSECONDmaintainAUTOMATICbattery life inSHUTthe caseOFFof accidental actuation, this unit will shut itself off after 45 seconds of continuous operation. The LED will flash rapidly for 5 seconds before the unit turns off.
7