625116-00 NPP2018 Pole 11/12/04 9:11 AM Page 8

Preparing Your Pole Trimmer for Use

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

Installing and Removing Saw Chain

WARNING: Sharp moving blade. To prevent accidental operation, insure that battery is disconnected from the handle before performing the following operations. Failure to do this could result in serious personal injury.

CAUTION: Sharp moving blade. Always wear protective gloves when installing or removing the chain. The chain is sharp and can cut you when it is not running.

•Place new chain in groove of guide bar and around sprocket. Make sure saw teeth are facing correct direction by matching arrow on chain with graphic on housing shown here.

• Rotate the screw in the front of the housing clockwise to increase the chain tension as in Figure 3.

•Replace sprocket cover, bar clamp, and allen head screws.

•Follow instructions for adjusting the chain tension.

Adjusting Chain Tension

4

• With the saw still on a firm surface

check the chain tension. The tension

 

is correct when the chain snaps back

 

after being pulled 1/8” (3mm) away

 

•Place the saw on a firm surface. Rotate the two allen head screws counterclockwise with the wrench provided as shown in figure 2.

•Remove sprocket cover, bar clamp, and allen head screws.

•To remove the chain, rotate the screw in the front of the housing using the flat screwdriver end of the wrench as shown in figure 3. Turning the screw counterclockwise allows the guide bar to recede and reduces the tension on the chain so that it may be removed.

•Lift the worn chain out of the groove in the guide bar.

•Flip guide bar over.

•To replace the chain, check to make sure that the slot in the guide bar is over the two location pins shown in figure 3A and that the hole below the slot is located over the adjustment pin.

2

3

3A

LOCATING PINS

ADJUSTMENT PIN

 

from the chain bar with light force

 

 

from the middle finger and thumb as

 

 

shown in figure 4. There should be

 

 

no “sag” between the guide bar and the

5

 

chain on the underside as shown in

 

figure 5.

 

•

To adjust saw chain tension, loosen

 

 

allen head screws

 

•

Rotate the screw in the front of the

 

 

housing using the flat screwdriver end

 

of the wrench as shown in figure 3.

•Do not over-tension the chain as this will lead to excessive wear and will reduce the life of the bar and chain. Overtensioning also reduces the amount of cuts you will get per battery charge.

•Once chain tension is correct, tighten allen head screws to clamp bar.

•When the chain is new check the tension frequently (after disconnecting battery) during the first 2 hours of use as a new chain stretches slightly.

8

Page 7 Page 9
Page 8
Image 8
Black & Decker NPP2018 Installing and Removing Saw Chain, Adjusting Chain Tension, With the saw still on a firm surface
Page 7 Page 9

NPP2018R, NPP2018 specifications

The Black & Decker NPP2018 is a powerful and innovative outdoor tool designed for homeowners who want to maintain their yards with ease and efficiency. This electric pole saw features an 18-volt lithium-ion battery that delivers impressive cutting performance while providing the convenience of being cordless. With a lightweight design and user-friendly features, the NPP2018 is ideal for trimming branches, pruning trees, and tackling tough overgrown areas.

One of the standout features of the Black & Decker NPP2018 is its extendable reach. The telescoping pole allows for an adjustable length, extending up to 10 feet, enabling users to access hard-to-reach branches without the need for a ladder. This not only enhances safety but also makes it easier to complete tasks without additional assistance.

The saw is equipped with a 10-inch Oregon bar and chain, which offers efficient cutting and reduced kickback, allowing for smooth operation. The automatic oiling system ensures that the bar and chain are constantly lubricated, significantly extending the tool’s life and maintaining optimal cutting performance. This technology reduces the time and effort required for maintenance, allowing users to focus more on the job at hand.

Additionally, the NPP2018 features a lightweight construction, weighing approximately 6.5 pounds, which enhances portability and maneuverability. The ergonomic handle design provides a comfortable grip and minimizes user fatigue, making it easier to operate for extended periods.

Black & Decker also emphasizes safety with the NPP2018, incorporating a protective sheath for the blade and an easy-to-use safety switch to prevent accidental starts. These features promote secure operation, especially for inexperienced users or those unfamiliar with power tools.

In summary, the Black & Decker NPP2018 is a versatile and effective tool for any homeowner looking to manage their outdoor spaces. With its powerful lithium-ion battery, extendable reach, automatic oiling system, and ergonomic design, this pole saw represents an innovative solution for tackling tree pruning and branch trimming tasks efficiently and safely. Whether you are a gardening novice or a seasoned pro, the NPP2018 delivers the durability and performance needed for effective yard maintenance.
Top Page Image Contents