Manuals / Black Box / Computer Equipment / Modem

Black Box MD403A user manual Install Hardware Device Drivers screen

Models: MD403A

1 87

Download 87 pages 18.06 Kb

Page 23

PORTABLE USB MODEM

4.The Install Hardware Device Drivers screen appears, indicating that it will install the hardware device drivers.

Portable USB Modem

Figure 3-3. Install Hardware Device Drivers screen.

Verify that “Search for a suitable driver for my device (recommended)” is selected, and click Next >.

22

Image 23

Black Box MD403A user manual Install Hardware Device Drivers screen

Contents

Portable USB Modem Users’ Manual FCC and IC RFI Statements EMC, Safety and R&TTE Directive Compliance FCC Requirements for Telephone-Line Equipment Certification Notice for Equipment Used in Canada NOM Statement Portable USB Modem Trademarks Used in this Manual Contents Contents Command Buffer 40 characters SpecificationsAGC Dynamic Range 43 dB Frequency Stability ±0.01%Temperature Tolerance 32 to 120F 0 to 50C Overview IntroductionWhat Can You Do with Your Modem? What the Package IncludesUniversal Serial Bus USB Features Required Equipment Connections USB and communications connectorsFront panel Front PanelConnect the Modem to Your System InstallationInstalling the Modem Welcome screen Install Hardware Device Drivers screen Locate Driver Files screen Driver Files Search Results screen Digital Signature Not Found screen appears Click Yes to continue with the installationCompletion screen Installation in Windows ME Portable USB Modem Add New Hardware Wizard screen What do you want Windows to do? screen 10. Windows will search for a new driver screen 11. Updated driver found screen 12. Verification screen 13. Finish screen Go to Start Settings Control Panel Click Start Settings Control PanelConfiguring the Modem for Your Country References AT Commands AT Commands, S-Registers, and Result CodesAnswer Repeat Last CommandCommunication Standard Setting Enter KeyATDT1028807637853500$123456789 Carrier ControlDial Hook Control Echo Command Mode CharactersDS=y Dial Stored Telephone Number Echo Online Data CharactersPulse Dialing Monitor Speaker ModeReturn Online to Data Mode Modulation HandshakeTone Dialing Result Codes Enable/DisableSr=n Set Register Value Sr? Read Register ValueAuto Retrain Modem ResetResult Code Selection Long Space Disconnect22bis Guard Tone Control Load Factory SettingsData Carrier Detect DCD Control ON/X-OFF Pacing ControlData Set Ready DSR Control Asynchronous Communications ModeTest Commands Flow Control SelectionZy=x Store Dialing Command Display Current SettingsStore Current Configuration Select Stored Configuration for Hard Reset\Kn Break Control \Bn Transmit Break\Gn Modem Port Flow Control \Jn Data Buffer Control\Nn Error Correction Mode Selection Online command mode. The modem receives a\Xn ON/X-OFF Pass-Through \Tn Inactivity Timer\Qn Flow Control Selection \Vn Protocol Result CodeData Compression Control Adaptive Answer Result Code Enable#Sx Enter Setup Password View Numbers in Blacklist+++ATCR Escape Sequence Atcr Remote Configuration Escape Sequence#S=x Registers Unit Range Default DescriptionSeconds 255 Unit Range Default Description Upstream data rates S48=7 S48=128 Verbose Description Result CodesConnected at 2400 bps Terse Verbose Description Introduction Remote ConfigurationBasic Procedure SetupChanging the Setup Password Modem Does Not Respond to Commands TroubleshootingNone of the Indicators Light Modem Dials But Cannot Connect Modem Disconnects While Online Fax and Data Software Can’t Run at the Same Time Modem Cannot Connect When AnsweringModem Doesn’t Work with Caller ID Shipping and Packaging Calling Black BoxAppendix A. V.90 Support V.90 TroubleshootingAppendix B. Loopback Tests Figure B-1. Local analog loopback test Local Analog Loopback Test V.54 LoopFigure B-2. Remote digital loopback test Remote Digital Loopback Test V.54 LoopFigure B-3. Local digital loopback test Local Digital Loopback Test V.54 LoopAppendix B Loopback Tests Appendix C. Dial-Up Networking Windows 98/Me Dial-Up Networking Figure C-3. Dial-Up connection created Figure C-4. Networking tab Figure C-5. TCP/IP Settings dialog box Figure C-6. Network Connection Wizard dialog box Windows 2000 Dial-Up NetworkingFigure C-7. Network Connection Type dialog box Figure C-8. Welcome to the Internet World Connection Wizard If you select Accept incoming connections Internet account connection, and click NextIf you select Connect directly to another computer Appendix D. Upgrading Modem Upgrade OverviewAppendix D Upgrading the Modem Copyright 2004. Black Box Corporation. All rights reserved