Manuals / Black Box / Computer Equipment / Modem

Black Box MD403A user manual Verification screen

Models: MD403A

1 87

Download 87 pages 18.06 Kb

Page 34

CHAPTER 3: Installation

8.The Add New Hardware Wizard dialog box indicates that Windows will select the proper driver from the Modem Installation CD and will display the information for verification.

Portable USB Modem

Figure 3-12. Verification screen.

Click Next > to install the selected driver.

33

Image 34

Black Box MD403A user manual Verification screen

Contents

Portable USB Modem Users’ Manual FCC and IC RFI Statements EMC, Safety and R&TTE Directive Compliance FCC Requirements for Telephone-Line Equipment Certification Notice for Equipment Used in Canada NOM Statement Portable USB Modem Trademarks Used in this Manual Contents Contents Specifications Command Buffer 40 charactersFrequency Stability ±0.01% AGC Dynamic Range 43 dBTemperature Tolerance 32 to 120F 0 to 50C Introduction OverviewUniversal Serial Bus USB What the Package IncludesWhat Can You Do with Your Modem? Features Required Equipment USB and communications connectors ConnectionsFront Panel Front panelInstallation Connect the Modem to Your SystemInstalling the Modem Welcome screen Install Hardware Device Drivers screen Locate Driver Files screen Driver Files Search Results screen Click Yes to continue with the installation Digital Signature Not Found screen appearsCompletion screen Installation in Windows ME Portable USB Modem Add New Hardware Wizard screen What do you want Windows to do? screen 10. Windows will search for a new driver screen 11. Updated driver found screen 12. Verification screen 13. Finish screen Click Start Settings Control Panel Go to Start Settings Control PanelConfiguring the Modem for Your Country References AT Commands, S-Registers, and Result Codes AT CommandsEnter Key Repeat Last CommandCommunication Standard Setting AnswerDial Carrier ControlATDT1028807637853500$123456789 Echo Online Data Characters Echo Command Mode CharactersDS=y Dial Stored Telephone Number Hook ControlModulation Handshake Monitor Speaker ModeReturn Online to Data Mode Pulse DialingSr? Read Register Value Result Codes Enable/DisableSr=n Set Register Value Tone DialingLong Space Disconnect Modem ResetResult Code Selection Auto RetrainON/X-OFF Pacing Control Load Factory SettingsData Carrier Detect DCD Control 22bis Guard Tone ControlFlow Control Selection Asynchronous Communications ModeTest Commands Data Set Ready DSR ControlSelect Stored Configuration for Hard Reset Display Current SettingsStore Current Configuration Zy=x Store Dialing Command\Jn Data Buffer Control \Bn Transmit Break\Gn Modem Port Flow Control \Kn Break ControlOnline command mode. The modem receives a \Nn Error Correction Mode Selection\Vn Protocol Result Code \Tn Inactivity Timer\Qn Flow Control Selection \Xn ON/X-OFF Pass-ThroughView Numbers in Blacklist Adaptive Answer Result Code Enable#Sx Enter Setup Password Data Compression Control#S=x Atcr Remote Configuration Escape Sequence+++ATCR Escape Sequence Unit Range Default Description RegistersSeconds 255 Unit Range Default Description Upstream data rates S48=7 S48=128 Result Codes Verbose DescriptionConnected at 2400 bps Terse Verbose Description Setup Remote ConfigurationBasic Procedure IntroductionChanging the Setup Password None of the Indicators Light TroubleshootingModem Does Not Respond to Commands Modem Dials But Cannot Connect Modem Disconnects While Online Modem Doesn’t Work with Caller ID Modem Cannot Connect When AnsweringFax and Data Software Can’t Run at the Same Time Calling Black Box Shipping and PackagingV.90 Troubleshooting Appendix A. V.90 SupportAppendix B. Loopback Tests Local Analog Loopback Test V.54 Loop Figure B-1. Local analog loopback testRemote Digital Loopback Test V.54 Loop Figure B-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure B-3. Local digital loopback testAppendix B Loopback Tests Appendix C. Dial-Up Networking Windows 98/Me Dial-Up Networking Figure C-3. Dial-Up connection created Figure C-4. Networking tab Figure C-5. TCP/IP Settings dialog box Windows 2000 Dial-Up Networking Figure C-6. Network Connection Wizard dialog boxFigure C-7. Network Connection Type dialog box Figure C-8. Welcome to the Internet World Connection Wizard Internet account connection, and click Next If you select Accept incoming connectionsIf you select Connect directly to another computer Upgrade Overview Appendix D. Upgrading ModemAppendix D Upgrading the Modem Copyright 2004. Black Box Corporation. All rights reserved