Manuals / Brands / Lawn and Garden / Patio Heater / Blue Rhino / Lawn and Garden / Patio Heater

Blue Rhino 450000 touching, after use, FOR YOUR SAFETY, • Do NOT touch or move, • Dome is hot to the touch, • Allow dome to cool before, heater for at least 45 minutes

1 44

Download 44 pages, 2.45 Mb

Contact 1-800-762-1142 for assistance.	®
Do not return to place of purchase.


Maintenance
Maintenance		WARNING
To enjoy years of outstanding performance from your heater, make sure		WARNING
		FOR YOUR SAFETY
you perform the following maintenance activities on a regular basis:		FOR YOUR SAFETY
Keep exterior surfaces clean.		• Do NOT touch or move
Use warm soapy water for cleaning. Never use flammable or corrosive		• Do NOT touch or move
		heater for at least 45 minutes
cleaning agents.		after use.
While cleaning your unit, be sure to keep the area around the burner		after use.
		• Dome is hot to the touch.
and pilot assembly dry at all times. Do not submerge the control valve		• Dome is hot to the touch.
assembly. If the gas control is submerged in water, do NOT use it. It		• Allow dome to cool before
must be replaced.		• Allow dome to cool before
must be replaced.		touching.
Air flow must be unobstructed. Keep controls, burner, and circulating air		touching.

passageways clean. Signs of possible blockage include:

Gas odor with extreme yellow tipping of flame.

Heater does NOT reach the desired temperature.

Heater glow is excessively uneven.

Heater makes popping noises.

Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles.

Carbon deposits may create a fire hazard. Clean dome and emitter with warm soapy water if any carbon deposits develop.

Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly.

TIP:

Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes.

Owner’s manual: model 200209 outdoor patio heater

7/28/04

18

Contents

Page Page Page Before you do anything else read and understand all precautions in Safety First “20 lb.” LP Tank Beware of Spiders Need a tank or gas Page General Components & Features Additional Requirements Step 1 – Attach Legs to Base Step 2 – Attach Platform to Legs Step 3 – Attach Weight Plate to Base Step 4 – Insert Gas Line through Platform/Attach Shroud Cover Step 5 – Attach Engine to Post Step 6 – Attach Engine/Post to Platform Step 7 – Connect Gas Line to Engine Step 8 – Assemble dome Step 9 – Attach Dome to Emitter Step 10 – Secure Gas Line Step 11 – Connect Gas Line to Tank Step 12 – Check for Leaks Check Gas Line / Tank valve for leaks: Step 13 – Replace Engine Access Panel Step 14 – Install Igniter Battery Before Turning Gas Supply ON Before Lighting Lighting When heater is ON: Re-lighting Shut Down Before Operating After Operation If the problem is: And this condition exists: Then do this Pilot won’t light Pilot won’t stay lit • Do NOT touch or move heater for at least 45 minutes after use • Dome is hot to the touch • Allow dome to cool before Between uses: During periods of extended inactivity or when transporting: Page Page Si necesita ayuda llame al No devuelva el artículo al lugar de compra Page Antes de hacer nada más, lea y comprenda todas las instrucciones en ¡La Seguridad, lo Primero Bombona de PL de 9 kg Tenga cuidado con las arañas ¿Necesita una bombona de gas www.bluerhino.com Page Componentes Generales y Características Requisitos adicionales Paso 1 – Acoplar las patas a la base Paso 2 – Acoplar la plataforma a las patas Paso 3 – Acoplar la placa de lastre Paso 4 – Insertar la línea de gas a través de la plataforma Acoplar la cubierta de protección Paso 5 – Acoplar el motor al poste Paso 6 – Acoplar el motor/poste a la plataforma Paso 7 – Conectar la línea de gas al motor Paso 8 – Montar la cúpula Paso 9 – Acoplar la cúpula al emisor Paso 10 – Conectar la línea de gas al motor Paso 11 – Conectar la línea de gas a la bombona Paso 12 – Comprobar si hay fugas Compruebe si hay fugas en la línea de gas/bombona: Paso 13 – Volver a colocar el panel de acceso al motor Paso 14 – Instalación de la batería de encendido Antes de activar la alimentación de gas (ON) Antes del encendido Encendido Cuando el calentador está encendido (ON) Reencendido Apagado Antes de la puesta en marcha Tras su funcionamiento Si el problema es: La llama piloto no se enciende La llama piloto no sigue encendida El quemador no se enciende La llama del quemador es baja •No toque ni mueva el calentador durante al menos 45 minutos después de su uso •La cúpula está caliente al tacto •Deje que la cúpula se enfríe antes de tocarla Entre uso y uso: Durante períodos largos de inactividad o para su transporte Page Certificaciones: Consumo: Alcance calorífico: Combustible: Tamaño de la bombona: