SPECIAL FEATURES
How to Operate the Cycle
Completion Signal
1.Open door, hold down program button (see Beeper Table on right) and simultaneously turn the Dishwasher on.
2.Release program button.
a.For SHV 6803 and SHU9950 models: The display will blink with a code of “0”, “1” or “2”. You are in program mode.
• If the display blinks with a “0”, you will hear no signal (indicates OFF).
• If the display blinks with a “1”, you will hear a LOW volume signal.
• If the display blinks with a “2”, you will hear a HIGHER volume signal.
b.For all other models with the beeper function:
•If the machine beeps, then the Cycle Completion Signal has been enabled.
•When you push the button again and it does not beep, it means that the Cycle Comple- tion Signal has been disabled.
3.To change the program, press the program button until the desired setting is selected.
4.Turn the Dishwasher off to take it out of program mode.
* At the end of a wash cycle, the beeper will sound off two times, and again every 15 minutes until the dishwasher is turned off.
| MODEL |
|
| Program BUTTON |
|
| ||||||||
|
|
|
| |||||||||||
| SHU 9950 | Delay Start Hours |
| |||||||||||
|
|
|
| |||||||||||
| SHU 9910/9920 | Delicate/Econo |
| |||||||||||
|
|
|
| |||||||||||
| SHU 8800/8810 | Quick Wash |
| |||||||||||
|
|
|
| |||||||||||
| SHV 6800 | Delay Start Hours |
| |||||||||||
|
|
|
| |||||||||||
| SHV 4800 | Delicate/Econo |
| |||||||||||
|
|
|
| |||||||||||
| SHV 4300 | Delicate/Econo |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 36
Accomodating
Extra Tall Items
If you have extra tall items that cannot fit in the bottom rack without interfering with the upper spray arm or without hitting the top rack (max. height 22”), you can remove the upper rack. A special accessory, the Extra Tall Item Sprinkler, lets you run the dishwasher with top rack removed. See Figures 36 and 36.
Note: Be sure to remove the Extra Tall Item Sprinkler before you reinstall the top rack, oth- erwise the door could become damaged and not close properly.
Installing “Extra Tall |
|
|
Item Sprinkler” |
|
|
1. With top rack empty, remove it from the dish- |
|
|
washer by pulling the rack toward you to the |
|
|
point where you can lift it up and out, dis- |
|
|
engaging the wheels from the side rails. |
|
|
2. Place the “Extra Tall Item Sprinkler” over the |
|
|
top rack spray outlet at the back of the dish- |
|
|
washer tub and turn it clockwise to lock the |
|
|
sprinkler head in place. See Figure 37. |
|
|
3. Place the extra tall items in the bottom rack |
|
|
for washing, as shown in Figure 36. To |
|
|
remove the Extra Tall Item Sprinkler, turn it |
|
|
counterclockwise and pull it out. Then replace | Figure 37 |
|
the top rack. |
|
|
www.boschappliances.com | ENGLISH - 23 | |
