dryer (see page 8).
7. Have the gas supply connected by
install the exhaust air outlet on the

Note:

 

 

 

 

 

 

Note:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The maximum permitted number of 90°Please check with the Authority Having

 

CAUTION

 

 

elbows

(including

this side

exhaust

kit)

Jurisdiction

in

your area

to

verify

if a

gas

 

 

is

four!

 

 

 

 

 

 

dryer

can

be

installed

in

your

mobile

 

Do not slide dryer across

the floor if

 

 

 

 

 

 

home.

Once that

has

been

verified,

 

 

 

 

 

 

 

 

 

 

i

Special

tool for cutting

the hole ininstallation

of

the

dryer shall

conform to heightnadjustable feet have

been

 

prepared

side

panel is

required.

 

the

Manufactured

Home

Construction

extended. Feet and/or dryer base

 

Contact

local

dealer!

 

 

 

and

Safety

Standard,

Title 24 CFR, Partmay be damaged if dryer

is slid

Bottom

exhaust

kit

 

 

 

3280

{formerly the Federal Standard for

across

floor with heightnadjustable

 

 

 

Mobile

Home

Construction and

Safety,

 

feet extended.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Title 24, HUD (Part 280)}, and/or

 

 

10. Position and then level

the .dryer

 

 

 

 

 

 

 

 

Standard

CAN/CSAnZ240

MH.

 

 

 

 

 

 

 

 

 

 

 

Please use mobile home kit number

 

 

 

 

 

 

 

 

 

 

 

 

WTZ

1275 for

means

to

secure the

 

 

 

 

 

 

 

 

 

 

 

 

dryer

to

the

structure.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See

page 9 •Exhaust

Air

Connection"

 

 

 

 

 

 

 

 

 

 

 

 

for the exhaust duct installation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

instructions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The exhaust duct must be securely

 

 

 

 

 

 

 

 

 

 

 

 

fastened

to a

noncombustible

portion

 

 

 

 

 

 

 

 

 

 

 

 

of the

mobile

home structure

and must

 

 

 

 

 

 

 

 

 

 

 

not terminate beneath the mobile

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

part no.WTZ

1270

 

 

 

home.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note:

 

 

 

 

 

 

An opening to the outside

must

be

 

 

 

 

The maximum permitted number of 90°provided during installation. Insure that

 

 

 

 

elbows

(including

this side exhaust

kit)

the

free

area of the opening for the

 

 

 

 

is

four!

 

 

 

 

 

 

introduction

of

outside

air is

not

less

 

 

 

 

 

 

 

 

 

 

than twice the area of the

dryer

exhaust

 

 

 

LP

-

Gas

Kit

 

 

 

 

 

 

 

 

 

 

 

outlet

or

use

at

least

a

5 inch diameter

 

 

 

 

 

 

 

 

 

 

 

exhaust

or

at

least a

225squarein

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

exhaust duct for the opening.

 

 

 

 

Installation

\ step by step

 

 

 

1.

Unpack the dryer.

 

 

 

 

2.

Remove all objects from the drum.

 

 

 

3.

Check the dryer for visible

 

 

 

 

 

 

damage.

 

 

 

 

 

 

4.

Position the dryer near the

 

 

 

 

 

 

installation

location.

 

 

 

 

 

5.

If required, have customer service

 

 

 

 

part

no.WTZ

1280

 

 

change the

door

hinges to

the left

The

parts required

for the LP version

(see page

6).

 

 

can be obtained from your local dealer. 6.

If required,

have

customer

service

Please follow

the

installation

 

 

 

 

The dryer should be level with all four feet firmly on the ground. The dryer must not wobble. If the dryer is not level or if it does wobble, th feet must be adjusted. Adjust the heightnadjustable feet until the dryer does not rock and is level,

instructions supplied by the appropriate manufacturer!

Note:

Dryer must be checked for proper operation whenever the gas connections have been broken

Left hinge kit

part no.WTZ 1260

The door catch can be reversed if necessary. The door is hinged on the right at the factory.

Pedestal Mounting Kit

part no.WTZ 1295

If mounting the dryer on the pedestal follow the instructions supplied with the pedestal.

an qualified technician (see page 7).

8.Install exhaust duct, if necessary. Follow the installation instructions supplied by the appropriate manufacturer!

iIf space is very restricted, it is

recommended to fit the initial parts of the exhaust duct to the dryer before the dryer is moved to its final installation location.

9.Move the dryer to its final location and align.

both frontntonback and sidentonside.

11.Connect the exhaust duct to the exhaust air outlet on the dryer.

12.Insert plug into the wall receptacle.

Mobile home kit

part no.WTZ 1275

9

Page 9
Image 9
Bosch Appliances WTMC6521UC Installation \ step by step, Bottom Exhaust Kit, Left hinge kit, Pedestal Mounting Kit