ADA Compliant |
|
HN200 | Installation Instructions |
Installation Instructions continued…
Step 4: Mount shower seat
NOTE: All anchoring devices (supplied by installer) must be carefully selected to insure adequate support for the shower seat, given the type of wall construction.
1. | Measure and scribe a horizontal line |
|
|
|
|
|
|
|
| |
| the finished floor (see Figure 4). |
|
|
|
|
|
|
|
| |
2. | Position the folding shower seat against the wall |
|
|
|
|
|
|
|
| |
| with the three mounting holes on the seat centered |
|
|
|
|
|
|
|
| |
| on the scribed line. |
|
|
|
|
|
|
|
| |
| • Using the mounting holes as a template, mark the |
|
|
|
|
|
|
|
| |
| three mounting locations on the wall. |
|
|
|
|
|
|
|
| |
3. | Install appropriate anchors (supplied by installer) for |
|
|
|
|
|
|
|
| |
| 1/4" sheet metal screws in the wall at the three |
|
|
|
|
|
|
|
| |
| mounting locations. |
| Figure 4 |
|
|
|
| |||
4. | Mount the shower seat to the wall with the |
|
|
|
|
|
|
|
|
|
| three 1/4" sheet metal screws (supplied) at |
|
|
|
|
|
|
| Figure 5 |
|
| the anchored mounting locations. |
|
|
|
|
|
|
|
|
|
| • Position the seat support tube in the |
|
|
|
|
|
|
|
|
|
| support bracket as shown in Figure 5. The |
|
|
|
|
|
|
|
|
|
| tube should rest on the bottom of the front |
|
|
|
|
|
|
|
|
|
| plate. |
|
|
|
|
|
|
|
|
|
NOTE: When seat is properly installed, it should |
|
|
|
|
|
|
|
|
| |
decline downward from back to front 2° to 3° for |
|
|
|
|
|
|
|
|
| |
water drainage. |
|
|
|
|
|
|
|
|
| |
5. | Place the support bracket against the wall |
|
|
|
|
|
|
|
|
|
| and adjust the bracket vertically until the |
|
|
|
|
|
|
|
|
|
| shower seat is level in down position. |
|
|
|
|
|
|
|
|
|
| • Using the mounting holes on the support |
|
|
|
|
|
|
|
|
|
| bracket as a template, mark the four |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| mounting locations on the wall. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
6. | Install appropriate anchors (supplied by installer) for |
|
|
|
|
|
|
|
| |
| 1/4" sheet metal screws in the wall at the four |
|
|
|
|
|
|
|
| |
| mounting locations. |
|
|
|
|
|
|
|
| |
7. | Mount the support bracket to the wall with the four |
|
|
|
|
|
|
|
| |
| 1/4" sheet metal screws (supplied) at the anchored |
|
|
|
|
|
|
|
| |
| mounting locations. |
|
|
|
|
|
|
|
| |
Step 5: Install curtain rod |
|
|
|
|
|
|
|
| ||
1. | Measure and cut the stainless steel curtain rod to fit |
|
|
|
|
| ||||
|
|
| Figure 6 | |||||||
| the shower stall opening. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
2.Mount one shower rod flange 80" (2032mm) from the floor as close to the opening of shower stall as possible with two
•Insert one end of the shower rod into the flange.
•Slide the other shower rod flange onto the shower rod.
3.Position the shower rod and flange at the same dimensions as the first flange but on the opposite side of the shower stall opening.
4.Secure the flange to the wall with two
5.Install the ten hooks onto the curtain rod and hang the curtain onto the rod.
6 | Bradley Corporation • |
