Briggs & Stratton Power Products Standby Generator

Installation, Start-Up and Owner’s Manual

BEFORE INITIAL START-UP

Engine Oil

This engine is shipped from the factory filled with the recommended oil. Before starting the engine, check oil level and ensure that engine is serviced as described in the engine owner’s manual.

CAUTION

Any attempt to crank or start the engine before it has been properly serviced with the recommended oil will result in equipment failure.

Refer to engine manual for oil fill information.

Damage to equipment resulting from failure to follow this instruction will void warranty.

Oil Considerations

Your Standby Generator is equipped with an engine that has been pre-run at the factory and does not require the traditional “break-in” procedure.

The generator is filled with synthetic oil (API SJ/CF 5W- 30W).This allows for generator operation in the widest range of temperature and climate conditions.

NOTE: The use of synthetic oil DOES NOT alter the required oil change intervals described in the engine owner’s manual.

7.Ensure hardware on both positive and negative battery terminals is secure.

8.Reinstall 15 Amp fuse in control panel.

CAUTION

Installing the 15A fuse could cause the engine to start.

DO NOT install the 15 Amp fuse until all plumbing and wiring has been completed and inspected.

9.Reinstall service disconnect in disconnect box.

10.Set generator's “AUTO/OFF/MANUAL” switch to AUTO.

11.Reset exercise timer following instructions “Setting Exercise Timer” on page 19.

NOTE: With the battery installed and utility power available to the Transfer Switch, the battery receives a trickle charge whenever the engine is not running.The trickle charge only prevents self-discharge and cannot be used to recharge a battery that is completely discharged.

Fuel Supply System

Ensure that all fuel pipe connections are tight, secure and without leaks.

Ensure that all gas line shutoff valves are OPEN and that adequate fuel pressure is available whenever automatic operation is desired.

Battery Connection

The Standby Generator is supplied with a 12 Volt DC

33 Amp-Hour battery. It is a sealed, lead-acid rechargeable battery. It is installed in the unit and the battery cables are connected at the factory.The generator’s 15 Amp fuse has been removed to prevent the battery from discharging and the unit from starting during shipping.

If it is necessary to service the battery, proceed as follows:

1.Set generator's “AUTO/OFF/MANUAL” switch to OFF.

2.Pull service disconnect from disconnect box.

3.Remove 15 Amp fuse from control panel.

4.Service or replace battery as required.

5.Connect red battery cable to positive battery terminal (indicated by POSITIVE, POS, or (+).

6.Connect black battery cable to negative battery terminal (indicated by NEGATIVE, NEG, or (-).

FUEL SYSTEM SELECTION

The engine of your Standby Generator is factory calibrated to run on natural gas (NG). It may also be operated on liquid propane (LP).

To configure the fuel system for LP use:

1.LP fuel inlet pressure must be between 11 and 14 inches water column.

2.Set AUTO/OFF/MANUAL switch to OFF.

3.Pull service disconnect from disconnect box.

4.Remove 15 Amp fuse.

5.Change main jet in fuel mixer following instruction sheet provided in LP conversion kit.

NOTE: You will need a specialty tool, as described on page 9, to change the main jet.

6.Reinstall 15 Amp fuse.

7.Reinstall service disconnect in disconnect box.

17

Page 17
Image 17
Briggs & Stratton 01897-0 owner manual Before Initial START-UP, Fuel System Selection, Engine Oil, Fuel Supply System

01897-0 specifications

Briggs & Stratton 01897-0 is a popular engine model renowned for its performance and durability in various applications. It is primarily used in lawn mowers and other outdoor power equipment, making it an ideal choice for homeowners and landscaping professionals alike.

One of the standout features of the 01897-0 is its powerful engine. This model is equipped with a reliable four-stroke engine that provides robust power for optimal mowing efficiency. With a displacement of 500cc, it delivers a substantial amount of torque, making it suitable for handling thick grass and tough terrains effortlessly.

The engine design incorporates several advanced technologies aimed at improving performance and extending longevity. One such feature is the overhead valve (OHV) design, which enhances airflow and increases combustion efficiency. This results in better fuel economy and lower emissions, aligning with environmental standards while providing the power needed for demanding tasks.

Another notable characteristic of the Briggs & Stratton 01897-0 is its easy-starting system. The engine is designed with a recoil starter, which allows for a quick and effortless start-up. This is especially beneficial during busy mowing seasons when efficiency is paramount.

In terms of maintenance, the 01897-0 emphasizes user convenience. It features an accessible oil drain and replacement system, facilitating simple oil changes. The air filter can also be easily accessed and replaced, ensuring the engine maintains optimal performance for many years.

Furthermore, the engine is engineered for vibration reduction, enhancing user comfort during operation. This technology helps minimize fatigue, allowing for extended mowing sessions without discomfort. The lightweight design of the engine also contributes to easier maneuverability, making it a practical choice for users of all experience levels.

Finally, Briggs & Stratton is known for its commitment to quality, and the 01897-0 is no exception. It is built to withstand the rigors of outdoor use, ensuring reliability and durability even under challenging conditions. With a reputation for excellence and a proven track record, the Briggs & Stratton 01897-0 continues to be a preferred choice for those seeking performance and reliability in outdoor power equipment. Whether for residential or commercial use, this engine model remains a popular and trusted option for efficient lawn care.