Briggs & Stratton Power Products Standby Generator

Installation, Start-Up and Owner’s Manual

Shipment Contents

The Standby Generator is supplied with:

•Standby generator w/disconnect box

•Pre-attached mounting pad

•One 24” flexible hook-up hose

•Installation, start-up and owner’s manual

•Installation checklist

•Remote LED plate

•Oil drain tray

•Touch-up paint

•One spare 15A fuse

•LP conversion kit

•Roof hardware bag

Figure 1 — Standby Generator Clearances

 

Exhaust port must be

Exhaust

5 ft (152 cm) minimum

Port

distance from building

 

openings

General Location Guidelines

• Install the unit outdoors ONLY.

Required Specialty Tools/Equipment

Tool, P/N 19570, is required if you need to convert the generator from natural gas (NG) to liquid propane (LP).

Lifting the Generator

CAUTION! The generator weighs more than

280 pounds. Proper tools, equipment and qualified personnel should be used in all phases of handling and moving the generator.

•Place the unit in a prepared location that is flat and has provisions for water drainage.

•Install the unit where air inlet and outlet openings will not become obstructed by leaves, grass, snow, etc. If prevailing winds will cause blowing or drifting, you may need to construct a windbreak to protect the unit.

•Install the generator as close as possible to the Transfer Switch to reduce the length of wiring and conduit.

•Install the generator as close as possible to the fuel supply to reduce length of pipes.

CAUTION! DO NOT lift unit by roof as damage to generator will occur.

Lifting pockets are provided at each corner between the base of the generator and its mounting pad. Retouch any chipped paint with supplied touch-up paint.

Standby Generator Location

Before installing generator, consult with homeowner and convey the following guidelines which may affect the desired location.

Generator Clearances

The generator enclosure must be a minimum of 3 ft. (92 cm) from combustible material. Leave at least 3 ft. (92 cm) all around the enclosure for access to the inside of the enclosure.

The unit’s exhaust port must be at least 5 ft. (152 cm) from any building opening (window, door, vent etc.), and the exhaust must not be able to accumulate in any occupied area (Figure 1).

IMPORTANT: Laws or local codes may regulate the distance to the fuel supply.

The Standby Generator is shipped already attached to its mounting pad. Unless mandated by local code, a concrete slab is not required.

If mandated by local code, construct a concrete slab at least 3 inches thick and 6 inches longer and wider than the unit. Attach unit to slab with 1/4” diameter (minimum) masonry anchor bolts long enough to retain the unit.

Essential Circuits

Consult with owner to clearly identify the circuits in building that are "essential".

It is important that you understand which circuits the owner wants to include as "Essential Circuits". Depending on the power consumed by these circuits, most or all of them can be switched to the Standby Generator for the duration of normal power interruption.

9

Page 8 Page 10
Page 9
Image 9
Briggs & Stratton 01897-0 Shipment Contents, Required Specialty Tools/Equipment, Lifting the Generator, Essential Circuits
Page 8 Page 10

01897-0 specifications

Briggs & Stratton 01897-0 is a popular engine model renowned for its performance and durability in various applications. It is primarily used in lawn mowers and other outdoor power equipment, making it an ideal choice for homeowners and landscaping professionals alike.

One of the standout features of the 01897-0 is its powerful engine. This model is equipped with a reliable four-stroke engine that provides robust power for optimal mowing efficiency. With a displacement of 500cc, it delivers a substantial amount of torque, making it suitable for handling thick grass and tough terrains effortlessly.

The engine design incorporates several advanced technologies aimed at improving performance and extending longevity. One such feature is the overhead valve (OHV) design, which enhances airflow and increases combustion efficiency. This results in better fuel economy and lower emissions, aligning with environmental standards while providing the power needed for demanding tasks.

Another notable characteristic of the Briggs & Stratton 01897-0 is its easy-starting system. The engine is designed with a recoil starter, which allows for a quick and effortless start-up. This is especially beneficial during busy mowing seasons when efficiency is paramount.

In terms of maintenance, the 01897-0 emphasizes user convenience. It features an accessible oil drain and replacement system, facilitating simple oil changes. The air filter can also be easily accessed and replaced, ensuring the engine maintains optimal performance for many years.

Furthermore, the engine is engineered for vibration reduction, enhancing user comfort during operation. This technology helps minimize fatigue, allowing for extended mowing sessions without discomfort. The lightweight design of the engine also contributes to easier maneuverability, making it a practical choice for users of all experience levels.

Finally, Briggs & Stratton is known for its commitment to quality, and the 01897-0 is no exception. It is built to withstand the rigors of outdoor use, ensuring reliability and durability even under challenging conditions. With a reputation for excellence and a proven track record, the Briggs & Stratton 01897-0 continues to be a preferred choice for those seeking performance and reliability in outdoor power equipment. Whether for residential or commercial use, this engine model remains a popular and trusted option for efficient lawn care.
Top Page Image Contents