Briggs & Stratton Power Products Standby Generator

Installation, Start-Up and Owner’s Manual

THE GASEOUS FUEL SYSTEM

WARNING

Propane and Natural Gas are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

•LP gas is heavier than air and will settle in low areas.

•Natural gas is lighter than air and will collect in high areas.

•The slightest spark can ignite these fuels and cause an explosion.

The information provided below is to assist gaseous fuel system technicians in planning installations. In no way should this information be interpreted to conflict with applicable fuel gas codes. Consult with your local fuel supplier or Fire Marshall if questions or problems arise.

Consult with the Standby Generator owner(s) and convey any technical considerations that might affect their installation plans before applying these general guidelines.

The following general rules apply to gaseous fuel system piping:

•The piping should be of a material that conforms to federal and local codes, rigidly mounted and protected against vibration.

•Install flexible gaseous pipe (supplied) between the standby generator fuel inlet port and rigid piping.

CAUTION

The supplied flexible gaseous pipe is not to be installed underground or in contact with the ground.

•The entire flexible gaseous pipe must be visible for periodic inspection and must not be concealed within, contact, or run through any wall, floor, or partition.

•Piping must be of the correct size to maintain the required supply pressures and volume flow under varying conditions.

•Use an approved pipe sealant or joint compound on all threaded fittings to reduce the possibility of leakage.

•Installed piping must be properly purged and leak tested, in accordance with applicable codes and standards.

Consider the following factors when planning to install the fuel supply system:

The Standby Generator engine is fitted with a fuel mixer system that meets the specifications of the California Air Resources Board for “tamper-proof” dual fuel systems.The unit will run on natural gas or liquefied propane.

•A minimum of one manual shutoff valve should be placed in the fuel supply line and located outside the building to facilitate servicing the generator.

•Natural gas fuel supply pressure at the generator's fuel inlet port should be between 5 to 7 inches of water (in. W.C.) at full load. LP fuel supply pressure should be 11 to 14 inches of water (in.W.C.) at full load.

The Standby Generator unit has been factory set to

run on natural gas. If you need to change from natural gas to LP gas, the unit will need to be reconfigured, as described on page 17.

It is recommended that the fuel connection incorporate the following components:

•A manual fuel shut-off valve located in the interior of the building.

•A manual fuel shut-off valve located outside the building, just before the generator unit.

•The termination of hard piping should include a sediment trap.

•A manometer port should be provided.

12

Page 11 Page 13
Page 12
Image 12
Briggs & Stratton 01897-0 owner manual Gaseous Fuel System, Standby Generator unit has been factory set to
Page 11 Page 13

01897-0 specifications

Briggs & Stratton 01897-0 is a popular engine model renowned for its performance and durability in various applications. It is primarily used in lawn mowers and other outdoor power equipment, making it an ideal choice for homeowners and landscaping professionals alike.

One of the standout features of the 01897-0 is its powerful engine. This model is equipped with a reliable four-stroke engine that provides robust power for optimal mowing efficiency. With a displacement of 500cc, it delivers a substantial amount of torque, making it suitable for handling thick grass and tough terrains effortlessly.

The engine design incorporates several advanced technologies aimed at improving performance and extending longevity. One such feature is the overhead valve (OHV) design, which enhances airflow and increases combustion efficiency. This results in better fuel economy and lower emissions, aligning with environmental standards while providing the power needed for demanding tasks.

Another notable characteristic of the Briggs & Stratton 01897-0 is its easy-starting system. The engine is designed with a recoil starter, which allows for a quick and effortless start-up. This is especially beneficial during busy mowing seasons when efficiency is paramount.

In terms of maintenance, the 01897-0 emphasizes user convenience. It features an accessible oil drain and replacement system, facilitating simple oil changes. The air filter can also be easily accessed and replaced, ensuring the engine maintains optimal performance for many years.

Furthermore, the engine is engineered for vibration reduction, enhancing user comfort during operation. This technology helps minimize fatigue, allowing for extended mowing sessions without discomfort. The lightweight design of the engine also contributes to easier maneuverability, making it a practical choice for users of all experience levels.

Finally, Briggs & Stratton is known for its commitment to quality, and the 01897-0 is no exception. It is built to withstand the rigors of outdoor use, ensuring reliability and durability even under challenging conditions. With a reputation for excellence and a proven track record, the Briggs & Stratton 01897-0 continues to be a preferred choice for those seeking performance and reliability in outdoor power equipment. Whether for residential or commercial use, this engine model remains a popular and trusted option for efficient lawn care.
Top Page Image Contents