Manuals / Briggs & Stratton / Lawn and Garden / Portable Generator

Briggs & Stratton 030235-01 manual System Ground, Connecting to a Building’s Electrical System

Models: 030235-01

1 48
Download 48 pages 6.11 Kb
Page 8
Image 8

System Ground

The generator has a system ground that connects the generator frame components to the ground terminals on the AC output receptacles. The system ground is connected to the AC neutral wire (the neutral is bonded to the generator frame).

Special Requirements

There may be Federal or State Occupational Safety and Health Administration (OSHA) regulations, local codes, or ordinances that apply to the intended use of the generator. Please consult a qualified electrician, electrical inspector, or the local agency having jurisdiction:

•In some areas, generators are required to be registered with local utility companies.

•If the generator is used at a construction site, there may be additional regulations which must be observed.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical system must be made by a qualified electrician. The connection must isolate the generator power from utility power and must comply with all applicable laws and electrical codes.

WARNING

Generator produces hazardous voltage.

Failure to isolate generator from power utility can result in death or injury to electric utility workers due to backfeed of electrical energy.

•When using generator for backup power, notify utility company. Use approved transfer equipment to isolate generator from electric utility.

•Use a ground fault circuit interrupter (GFCI) in any damp or highly conductive area, such as metal decking or steel work.

•DO NOT touch bare wires or receptacles.

•DO NOT use generator with electrical cords which are worn, frayed, bare or otherwise damaged.

•DO NOT operate generator in the rain or wet weather.

•DO NOT handle generator or electrical cords while standing in water, while barefoot, or while hands or feet are wet.

•DO NOT allow unqualified persons or children to operate or service generator.

Generator Location

Clearances and Air Movement

WARNING

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•Keep at least 5 ft. (152 cm) clearance on all sides of generator including overhead.

Place generator in a well ventilated area, which will allow for removal of deadly exhaust gas. DO NOT place generator where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes, or other openings that can allow exhaust gas to collect in a confined area (Figure 3). Prevailing winds and air currents should be taken into consideration when positioning generator.

Using a generator indoors WILL KILL YOU IN MINUTES.

Exhaust contains carbon monoxide, a poison gas you cannot see or smell.

NEVER use in the home ONLY use outdoors and

or in partly enclosed far from open windows, areas such as garages. doors, and vents.

A

Figure 3 — Generator Clearance for Typical Generator A - Exhaust Port

6www.briggsandstratton.com

Page 7 Page 9
Page 8
Image 8
Briggs & Stratton 030235-01 manual System Ground, Connecting to a Building’s Electrical System, Generator Location
Page 7 Page 9

030235-01 specifications

The Briggs & Stratton 030235-01 is a key component in the realm of outdoor power equipment, renowned for its reliability and performance. This model is primarily designed for use in portable generators, offering a powerful and efficient engine that meets the demands of users looking for dependable energy solutions.

One of the standout features of the 030235-01 is its impressive engine output. With a robust design, it provides a reliable source of power for various applications, whether for home backup during outages or for job sites requiring portable energy. This model is built with a reliable four-stroke engine, allowing for smooth operation and reduced emissions compared to two-stroke engines. This makes it an environmentally friendly option for those needing outdoor power.

The motor is equipped with advanced technologies that enhance its performance. The overhead valve (OHV) design optimizes engine efficiency while maintaining low operating temperatures, ensuring longer life and reduced wear. Additionally, the engine features a splash lubrication system, taking care of critical components to minimize friction and ensure a smooth operation even under heavy loads.

Another key characteristic of the Briggs & Stratton 030235-01 is its easy-starting capability. Many users appreciate this feature, especially during emergencies when time is of the essence. The primer bulb and choke system facilitate a hassle-free startup, allowing users to get the engine running with minimal effort.

Durability is also a key focus of this engine's design. Constructed with high-quality materials and comprehensive engineering, the 030235-01 can withstand the rigors of frequent use. It has a sturdy build that resists corrosion, making it suitable for various outdoor conditions. Coupled with routine maintenance, this generator can serve users for years to come.

On the ease of use front, the Briggs & Stratton 030235-01 is designed for straightforward operation. It has an intuitive control panel that enables users to manage their power needs without any confusion, enhancing the overall user experience.

In summary, the Briggs & Stratton 030235-01 stands out for its powerful engine output, innovative technologies such as OHV design and splash lubrication, durability under various conditions, and user-friendly operation. This combination makes it a preferred choice for those seeking reliable portable power solutions.