Lap-Belt Installation, Facing on vehicle seat

Installation: Rear-facing

Lap-Belt Installation

• Figure A illustrates a typical rear-facing, lap-belt installation.

• When not in use, always store the LATCH connectors in storage slots. See page 30.

1 Fully recline the child seat, then place it rear-	A Rear-Facing
facing on vehicle seat.

•See Recline Adjustment on page 30.

2 Lift the child seat cover and open rear-facing lock-off farthest from where the vehicle belt will be buckled (Fig. B).

3 Pull the vehicle belt out and pass it through the closest rear-facing belt slot (Fig. C).

• The vehicle belt can be routed over or under the B child seat cover.

4 Route the vehicle belt across the child seat then through the second rear-facing belt slot.

IMPORTANT: The vehicle belt must rest behind the child seat buckle.

5	Verify that the vehicle belt is not twisted and
	buckle (Fig. D).	C
6	Push the child seat ﬁrmly into the vehicle	C

8 Verify that the vehicle belt is tight and that the child seat is secure.

•When properly installed in the rear-facing position, the back angle of the child seat should be 30º – 45º from vertical (not to exceed 45º) when the car is parked on a level surface (Fig. F).

•If necessary, the proper recline angle can be achieved by placing a rolled towel or pool noodle in the crease of the vehicle seat to level the child seat’s base.

•Rear-facing installation can be improved by the use of the Versa-Tether®see pages 25 – 28.

•The child seat is secure when it cannot be moved more than one inch (2.5 cm) front-to-back or side- to-side at the belt path.

WARNING! Do not raise the child seat off the front edge of the vehicle seat. This could cause your child seat not to

perform as intended.

Removal

0º 30–45º

F	90º

seat while removing slack from the vehicle belt.

7 Position the vehicle belt through the lock-off, tighten the belt,

then close the lock-off arm (Fig. E) and replace the cover.

•Lock-off is properly closed when a positive click is heard.

•To prevent breakage, never extend the lock-off arm beyond its normal open position and always keep lock-off closed when not in use.

•If your vehicle is equipped with an automatic locking retractor (ALR), use of lock-offs is not required as long as the ALR is locked. Check your vehicle owner’s manual to determine what type of retractor your vehicle has, and how to lock the retractor.

•If connected, disconnect the Versa-Tether®from the tether anchor.

•Press the red release button on the vehicle belt buckle and pull the vehicle buckle from the child seat belt path.

Roundabout specifications

The Britax Roundabout is a well-regarded convertible car seat that exemplifies safety, comfort, and convenience for parents and children alike. Designed to accommodate children from approximately 5 to 65 pounds, it provides a versatile seating solution suitable for infants and toddlers as they grow.

One of the standout features of the Britax Roundabout is its dual mode functionality, allowing it to function as both a rear-facing and forward-facing car seat. This flexibility enables parents to keep their child in the safer rear-facing position for as long as possible, which is highly recommended by safety experts. The Roundabout easily transitions to forward-facing once the child surpasses the appropriate weight and height limits, making it a long-lasting investment.

Safety is paramount with the Britax Roundabout, which is equipped with innovative technologies designed to enhance protection during a collision. The seat incorporates Britax's SafeCell Impact Protection system, featuring a base that compresses to reduce the impact of a crash and protect the child’s head, neck, and spine. Additionally, the seat comes with side impact protection, which provides extra security in the event of a side collision.

Comfort is also a key aspect of the Roundabout's design. The seat features plush, padded fabric to ensure a cozy ride for your little one. The seat cover is also easy to remove and machine washable, providing convenience for parents when it comes to cleaning up spills and messes.

Installation of the Britax Roundabout is designed to be straightforward and user-friendly. It is equipped with the ClickTight Installation System, which allows for easy and secure installation using the vehicle's seat belt or LATCH system. This technology minimizes the risk of installation errors, which are common with other car seats.

Other notable characteristics include multiple recline positions for added comfort during long journeys and a 5-point harness system that ensures a secure fit for children of different sizes. The Roundabout is also known for its durable construction, which contributes to its longevity and reliability.

In summary, the Britax Roundabout is a convertible car seat that stands out due to its combination of safety features, user-friendly installation, and comfort. As children grow, the Roundabout adapts to their needs, making it a practical choice for parents seeking a dependable and versatile car seat for their family.

Britax Roundabout manual Lap-Belt Installation, Facing on vehicle seat

Models: Roundabout