1 99150591 Screw, #10 x 7/8" (4 required)*
2 97011410 Housing Assembly (includes Key No. 7)
3 98005512 Wiring Adapter Plate
4 99150471 Ground Screw, #10-32 x 1/2"
5 97008575 Wiring Harness
6 99260477 Whiz Nut, 1/4-20 (2 required)*
7 99420470 Grille Nut (2 required)
8 98005513 Outlet Box Cover
9 99400035 Strain Relief Bushing
10 97011394 Blower Wheel (MP100)
97011395 Blower Wheel (MP140)
97011396 Blower Wheel (MP200)
11 97011361 Blower Housing (MP100)
97011362 Blower Housing (MP140)
97011363 Blower Housing (MP200)
12 99100412 Motor Mounting Rubber (2 required)
13 97011400 Motor (MP100) (includes Key No. 16)
97011411 Motor (MP140) (includes Key No. 16)
97011402 Motor (MP200) (includes Key No. 16)
14 95000963 Motor Cup
15 99170245 Screw, #8 x 3/8" (10 required)*
16 97011403 Capacitor (MP100)
97011412 Capacitor (MP140)
97011405 Capacitor (MP200)
17 97011406 Cover
18 99110942 Inlet Cover (covers unused inlet ports)
** 97011407 Blower Assembly Complete (MP100)
(includes Key No.s 10 thru 16)
** 97011413 Blower Assembly Complete (MP140)
(includes Key No.s 10 thru 16)
** 97011409 Blower Assembly Complete (MP200)
(includes Key No.s 10 thru 16)
DIFFUSER
CEILING
DRYWALL
DUCT
TAPE
OR
CLAMP
TO
VENTILATOR
4" ROUND
INSULATED
FLEXIBLE DUCT
DESCRIPTION
KEY PART
NO.
NO.
6
10
11
12
13 12
14
16
17
9
8
15 7
5
2
3
4
18
15
1
15
15
INSTALL EXHAUST DIFFUSERS

Follow instructions packed with diffuser(s). General instructions:

1. Cut hole(s) in ceiling drywall and install diffuser(s).

2. Connect insulated ductwork to diffuser(s) and use duct tape or

clamp (available separately) to seal connection(s).

3. Rotate center of diffuser(s) counterclockwise to fully open for

maximum air flow. Reduce air flow by rotating center of

diffuser(s) clockwise to desired opening. A balancing damper

(available separately) can be used to adjust airflow.

USE AND CARE

WARNING: DISCONNECT ELECTRICAL POWER AND LOCK

OUT SERVICE PANEL BEFORE CLEANING OR SERVICING

THIS UNIT.

CLEANING

A continuously operating in-line ventilator needs to be cleaned

once a year to assure proper performance.

Remove cover and carefully vacuum blower and inside of hous-

ing. Be careful not to bend or otherwise damage blower wheel.

Diffusers and intake vents can be vacuumed and/or wiped clean

with a damp cloth.

MOTOR LUBRICATION

The motor is permanently lubricated. Do not oil or disassemble

motor.

SERVICE PARTS

Models MP100, MP140 & MP200

* Standard Hardware - May be purchased locally.
** Not shown assembled. Always order replacement parts by “Part No, - not by “Key No.”
BROAN ONE YEAR LIMITED WARRANTY
Broan warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE
ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have
been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation
may not apply to you.
BROAN’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN SHALL NOT BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty
service, you must present evidence of the original purchase date. In the U.S., contact: Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)
In Canada, contact: Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 (1-888-882-7626)
99041951J