Bryant 355CAV Gas Rate cu Ft/Hr, Set Temperature Rise, Set Thermostat Heat Anticipator

Table 12 – Gas Rate cu Ft/Hr

SECONDS	SIZE OF TEST DIAL			SECONDS		SIZE OF TEST DIAL
FOR 1				FOR 1
	1	2	5		1		2	5
REVOLUTION				REVOLUTION
	cu ft.	cu ft.	cu ft.		cu ft.		cu ft.	cu ft.
10	360	720	1800	50	72		144	360
11	327	655	1636	51	71		141	355
12	300	600	1500	52	69		138	346
13	277	555	1385	53	68		136	340
14	257	514	1286	54	67		133	333
15	240	480	1200	55	65		131	327
16	225	450	1125	56	64		129	321
17	212	424	1059	57	63		126	316
18	200	400	1000	58	62		124	310
19	189	379	947	59	61		122	305
20	180	360	900	60	60		120	300
21	171	343	857	62	58		116	290
22	164	327	818	64	56		112	281
23	157	313	783	66	54		109	273
24	150	300	750	68	53		106	265
25	144	288	720	70	51		103	257
26	138	277	692	72	50		100	250
27	133	267	667	74	48		97	243
28	129	257	643	76	47		95	237
29	124	248	621	78	46		92	231
30	120	240	600	80	45		90	225
31	116	232	581	82	44		88	220
32	113	225	563	84	43		86	214
33	109	218	545	86	42		84	209
34	106	212	529	88	41		82	205
35	103	206	514	90	40		80	200
36	100	200	500	92	39		78	196
37	97	195	486	94	38		76	192
38	95	189	474	96	38		75	188
39	92	185	462	98	37		74	184
40	90	180	450	100	36		72	180
41	88	176	439	102	35		71	178
42	86	172	429	104	35		69	173
43	84	167	419	106	34		68	170
44	82	164	409	108	33		67	167
45	80	160	400	110	33		65	164
46	78	157	391	112	32		64	161
47	76	153	383	116	31		62	155
48	75	150	375	120	30		60	150
49	73	147	367

355CAV

Set Temperature Rise

!CAUTION

UNIT DAMAGE HAZARD

Failure to follow this caution may result in component damage.

Temperature rise must be within limits specified on unit rating plate. Operation is within a few degrees of midpoint of rise range when setup switch SW1-4 is OFF.

Furnace must operate within ranges of temperature rise specified on the furnace rating plate. Determine air temperature rise as follows:

1.Place thermometers in return and supply ducts as near fur- nace as possible. Be sure thermometers do not see heat ex- changer so that radiant heat does not affect readings. This practice is particularly important with straight-run ducts.

2.When thermometer readings stabilize, subtract return-air temperature from supply-air temperature to determine air temperature rise.

NOTE: Temperature rise can be determined for low-heat operation by placing setup switch SW1-2 on furnace control in

ON position. Temperature rise can be determined for medium-heat operation by placing setup switch SW4-2 on furnace control in ON position. For high-heat operation, place setup switch SW1-2 and SW4-2 in OFF position and jumper R-W2 on furnace control. DO NOT forget to return setup switch to OFF position and remove R-W2 jumper upon completion of testing. (See Fig. 33 for switch and terminal location.)

3.This furnace is capable of automatically providing proper airflow to maintain the temperature rise within the range specified on furnace rating plate. If temperature rise is out- side this range, proceed as follows:

a.Check gas input for low-, medium-, and high-heat oper- ation.

b.Check derate for altitude if applicable.

c.Check all return and supply ducts for excessive restric- tions causing static pressure greater than 0.5-in. wc.

d.Ensure Low Heat Rise Adjust switch SW1-3 on furnace control is in ON position when a bypass humidifier is used. (See Fig. 33 for switch location.)

e.Check Troubleshooting Guide for Variable-Speed Step Modulating Condensing Furnaces.

Set Thermostat Heat Anticipator

When using a non-electronic thermostat, the thermostat heat anticipator must be set to match the amp draw of components in

59