Service = LAST 10 SYSTEM FAULTS
This screen will show last 10 faults that occurred throughout the system. Each fault has the time and date incident recorded. Service technician should enter current date in ″TODAY’S DATE″ menu section BEFORE checking and logging the last 10 system faults. Each fault has a two-letter acronym preceding the fault name to identify which piece of equipment generated the fault. This fault history can be cleared under Thermostat Setup, Reset Factory Defaults.
•HP = heat pump
•AC = air conditioner
•FN = furnace
•FC = fan coil
•ZO = zoning
Service = RUN / FAULT HISTORY
The indoor unit and outdoor unit (if communicating) have the following histories:
NOTE: For Critical Fault Screens, see Troubleshooting section in this document.
Resettable Faults:
•Fault counters for each piece of equipment that can be reset. Cycle Counters:
•Number of heat/cool/power cycles the unit has performed. Run Times:
•Lifetime hours of operation in heating, cooling, and how long the unit has been powered.
Service = TODAY’S DATE
•This menu item allows the installer to enter the current date. It
is used for time/date stamping of system faults. This should be entered every time prior to viewing ″LAST 10 SYSTEM FAULTS″ section.
Service = MODEL / SERIAL NUMBERS
•This menu item allows the installer to view the model number and serial number (if available) of all communicating pieces of equipment in the system.
Service = SERVICE PHONE NUMBER
This menu item allows the installer to enter a name and phone number that the homeowner can call for future service of the system. This name and phone number will appear to the home- owner whenever a service reminder pop-up message is displayed (i.e. Change Filter, etc.)
To edit:
•Use Temp +/- button to move cursor left and right.
•Use Time +/- button to select numbers and letters.
•Use Scroll button to move up and down between NAME and
NUMBER.
OPERATIONAL INFORMATION
Zone Selection:
•Press top left ZONE button to select zones.
Continuous Fan Operation
Pressing FAN button will scroll through the following:
•AUTO = No fan operation except during equipment operation.
•LOW = Approximately 50% of High Speed operation.
•MED = Half way between High and Low speed operation.
•HIGH = Highest of either High Heating or High Cooling CFM.
Five-Minute Compressor Timeguard
This timer prevents compressor from starting unless it has been off for at least 5 minutes. It can be defeated by simultaneously pressing the Fan and Temp + buttons.
—12—
Emergency Heat (for heat pump applications)
To activate Emergency Heat, you must press and hold the HEAT button for 3 seconds to activate.
Keypad Lockout
Keypad can be locked by pressing ″Fan″ and ″Zone″ buttons at the same time for 3 seconds. When keys are locked, a lock symbol will appear in the upper left corner of screen. Follow same procedure to unlock keypad.
Heat and Cool LED
The Heat and Cool LEDs will pulsate during actual equipment operation.
Equipment Cycle Timer (adjustable 4-6 cycles per hour)
This timer prevents the start of a heating or cooling cycle until 15 (or 10) minutes after the last start of the same cycle. Its function is to assure that the equipment is not cycled more than the selected times per hour. This timer is adjustable from 4 to 6 cycles per hour. This timer is defeated for one cycle when the desired temperature is manually changed. It can also be defeated for one cycle by simultaneously pressing the Fan and Temp + buttons.
Ten-Minute Staging Timer
In multistage heating or cooling, this timer prevents any higher stage from turning on until the preceding stage has been on for 10 minutes. This timer is defeated if temperature error is greater than 5°F (usually due to a large change in desired temperature).
Three-Minute Minimum On Time
In normal operation, when a stage turns on, it will remain on for a minimum of three minutes. If the set point is changed, this timer is automatically cancelled, allowing the equipment to turn off imme- diately when the demand is removed.
Heat/Cool Set points (Desired Temperatures)
A minimum difference of 2° (default) is enforced between heating and cooling desired temperatures. This is done by allowing one setting to ″push″ the other to maintain this difference. This difference is adjustable via the Install/Service menu under Ther- mostat Setup.
Auto Changeover
When Auto mode is enabled (factory default) a change from heat to cool (or vice versa) will not occur until an opposite mode demand has existed for 30 minutes. If the set point is changed, the 30-minute requirement is defeated. This Auto Changeover time is adjustable via the Install/Service menu under Thermostat Setup. Range = 5 - 120 min.
Smart Recovery
With Smart Recovery selected (factory default), transition out of setback begins 1.5 hours before selected recovery time and gradually adjusts room temperature so desired temperature will be achieved at selected recovery time. It operates in both heating and cooling. This only applies to programmable operation.
Media Filter
If MEDIA or MEDIA+EAC is installed in the indoor unit, the system will perform a static pressure check of the system every 24 hours at 1:00PM to monitor filter accumulation (TrueSense™ Dirty Filter Detection) or whenever power is applied to the system or the system is transitioned from Off to Cool or Heat modes. The blower will run at a medium airflow for one minute.
Unoccupied
Pressing the HOLD button for 3 sec. will set the selected zone to unoccupied status.
All Zones
Pressing the zone button for 3 sec. will gray out the entire display and put the User Interface into All Zones mode (indicated by All Zones in upper left of the display). Any changes to set temperature, fan, or Hold status will occur in all zones when the screen is exited. Press the Zone button to exit All Zones mode.
