Bryant SYSTXBBUIZ01 instruction manual Equipment Summary Menu, Install Menu, Setup Menu

EQUIPMENT SUMMARY MENU

EQUIPMENT SUMMARY

FURNACE	355MAV0420
AC	598BNX024
FILTER	EAC
HUMIDIFIER	YES
UV LIGHTS	YES
ZONES	1234
BACK

A04108

Fig. 21 — EQUIPMENT SUMMARY

An example screen is shown in Fig. 21:

This screen shows indoor unit type and model number, outdoor unit type (and model number if a 2-speed unit), filter type, any accessories that are installed, and how many zones are recognized.

INSTALL MENU

INSTALL

TO ADD, UNINSTALL OR

RE-INSTALL EQUIPMENT,

PRESS RIGHT SIDE

BUTTON

BACK INSTALL

A03202

Fig. 22 — INSTALL

This menu item will perform start-up process in order to learn all equipment in system. Press right side button to initiate the process. See Fig. 22.

SETUP MENU

This menu has several layers, allowing modification of equipment settings. No settings will need to be made at equipment (i.e. DIP switches on a furnace). All configuration settings made effective from this menu will override equipment configuration made by dip switches. Fig. 23 shows all the information that can be found in the SETUP menu.

SETUP

THERMOSTAT

FURNACE

HEAT PUMP

ZONING

ACCESSORIES

SYSTEM MAINTENANCE

BACK SELECT

A04089

Fig. 23 — SETUP MENU

Setup = THERMOSTAT:

AUTO MODE SETUP:

•Enable/Disable Auto Changeover mode (default=Enable).

•Auto Changeover Time may be adjusted 5 to 120 minutes, (default = 30 minutes).

When Auto mode is enabled (factory default) a change from heat to cool (or vice versa) will not occur until an opposite mode demand has existed for 30 minutes. If the set point is changed, the 30 minute timer is deleted.

HEAT/COOL DEADBAND:

•0 to 6 degrees, (default = 2°).

A minimum difference of 2° is enforced between heating and cooling desired temperatures. This will allow one setting to ″push″ the other to maintain this difference.

—8—

OFFSETS: This option allows calibration (or deliberate miscali- bration) of the temperature and humidity sensors. These offsets are added to the actual temperature/humidity values (defaults = 0).

•Zone 1 Offset: -5 to +5 degrees.

•Outside Temp Offset: -5 to +5 degrees.

•Humidity Offset: -10 to +10 percent.

CYCLES PER HOUR:

•Maximum cycles per hour = 4 (default) or 6.

•Anticipator = 1 to 9 (default=3). This adjusts sensitivity to zone temperature changes. 1 = most sensitive, 9 = least sensitive.

PROGRAMMING:

•On or Off (default=On)

•Periods Per Day = 2 or 4 (default=4)

•Programmable Fan On/Off (default=Off). If ON is selected, fan can be set to Auto, Low, Med, or High independently in each zone.

SMART RECOVERY:

•On or Off, (default=On)

Applies to programmable operation only. Will start recovery 90 minutes prior to schedule change in both heating and cooling mode.

ENGLISH/METRIC DISPLAY:

•°F or °C, (default = °F)

RESET FACTORY DEFAULTS:

Program Schedule:

•Yes/No to reset back to Energy Star default Time and Temp schedules.

User Settings:

•Yes/No to reset the user settings in the Advanced Setup to factory default settings.

Install Settings:

•Yes/No to reset install settings in Install/Service menus to factory default settings.

Last 10 Faults:

•Yes/No to reset last 10 faults under Service Info menu.

Setup = FURNACE:

Upon a first time start-up of the Evolution Zone Control™, the furnace DIP switch settings will be copied to the furnace setup menu. Any changes can then be made from the Evolution Zone Control™.

AIRFLOW:

•COMFORT (default)

•EFFICIENCY

Selects the airflow of the furnace when heating. EFFICIENCY is the airflow used to meet specified ratings, COMFORT is a decreased airflow used to increase the output air temperature and provide increased comfort.

AC AIRFLOW:

•EFFICIENCY

•COMFORT (default)

•MAXIMUM

Selects the airflow of the furnace when cooling. COMFORT is a decreased airflow used to improve humidity control. EFFI- CIENCY is the airflow used to meet specified ratings. MAXI- MUM is a fixed airflow of 400 CFM/ton based on the outdoor unit size.

DEHUM AIRFLOW:

•NORMAL (default)

•HIGH