Zone Control
User Interface &
Smart Sensor(s)
A 
B 
C 
D
A 
B 
C 
D
|
|
|
|
|
|
| Indoor |
| ||||
|
|
|
|
|
|
|
| Unit | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Green |
|
|
|
| A |
| A |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Yellow |
| B |
| B | |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| White |
| C |
| C | |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| Red |
|
|
|
| D |
|
|
|
|
|
|
|
|
| D |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
A |
| B |
| C |
| D |
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
WARNING: FIRE OR EQUIPMENT HAZARD Failure to follow this warning could result in equipment damage or fire.
Do not apply 24vac fan powered humidifier (with internal power supply) direct to indoor unit HUM and COM terminals.
| Humidifier | HUM | |
|
|
| |
| Connection |
|
|
Damper |
| COM | |
Control |
| 24V | |
|
| OAT | |
module |
|
| |
|
| Sensor | |
|
|
| |
|
|
| (Optional) |
|
|
|
|
|
| OAT | |
Fig. 12 — Communicating Indoor Unit w/2-Speed Pu-
ron™ Communicating Outdoor Unit
INITIAL POWER-UP
NOTE: Refer to Functional Overview (Fig. 11) to become familiar with key function buttons such as ″System On/Off″, ″Zone″, ″Fan″,
A. Section 1 — Power Up Sequence
INDOOR UNIT | OUTDOOR UNIT |
Zone Control
User Interface &
Smart Sensor(s)
A 
B 
C 
D
A 
B 
C 
D
A 
B 
C 
D
A04018
Indoor
Unit
Green
A
Yellow
B
White
C
Red
D
1-Spd. AC
Humidifier HUM
Connection
ESTABLISHING | SEARCHING FOR | SEARCHING FOR |
COMMUNICATIONS | ||
WITH EQUIPMENT | INDOOR EQUIPMENT | OUTDOOR EQUIPMENT |
PLEASE WAIT |
|
|
SOFTWARE | WORKING | WORKING |
|
| |
VERSION |
|
|
A03195
Fig. 15 — Power Up Sequence
This section addresses initial power up (or commissioning) of a new Evolution Zone Control™. The User Interface will commu-
Damper Control module
COM | C |
24V |
|
Y/Y2 | Y |
OAT
OATSensor
nicate and identify all Evolution components in the system. The following is a typical example for a communicating Variable- Speed Furnace / Fan Coil with a
The User Interface display will light up and indicate that it is now
″
Fig. 13 — Connection Diagram for Furnace or FE Fan
Coil with 1-Speed AC
A04019
ESTABLISHING COMMUNICATIONS WITH EQUIPMENT PLEASE WAIT″. The User Interface will automatically continue by ″SEARCHING FOR INDOOR EQUIPMENT″, followed by ″SEARCHING FOR OUTDOOR EQUIPMENT″ (See Fig. 15). Once the indoor and outdoor equipment has been found, the
Zone Control
User Interface &
Smart Sensor(s)
A 
B 
C 
D
A 
B 
C 
D
A 
B 
C 
D
Fan Coil
Green
A
Yellow
B
White
C
Red
D
Humidifier | HUM |
|
Connection |
|
|
C | C | |
| ||
R |
| R |
Installer will be asked to select Accessories. Proceed to Section 4. Selecting Accessories.
NOTE: If the
Damper Control
O | O |
W | W2 |
Y |
|
B. Section 2 — Selecting Outdoor Unit
module
Y |
OUTDOOR UNIT | OUTDOOR UNIT | |
NOT IDENTIFIED | ||
|
OUTDOOR UNIT
OAT
OATSensor
Fig. 14 — Connection Diagram for FE Fan Coil with
1-Speed HP
A04020
|
| ENTER HEAT PUMP | ||
SELECT TYPE: | NONE | SIZE |
| 36000 BTU |
NONE, AC, HP |
| 18000 TO 60000 BTU | ||
|
| |||
PRESS +/- TO MAKE | PRESS +/- TO MAKE | |||
SELECTION | SELECTION | |||
CONTINUE | BACK | CONTINUE | ||
HEAT PUMP |
| |
ENTER NUMBER OF |
| |
SPEEDS, 1 or 2: | 1 | |
PRESS +/- TO MAKE |
| |
SELECTION |
| |
BACK | CONTINUE | |
A03196
isolation relay coil to furnace or fan coil HUM and COM terminals will allow the Evolution Zone Control to automatically energize the HUM output during a call for humidification. The N.O. relay contacts will be used to energize the humidifier. See fan powered humidifier installation instructions for more details.
Fig. 16—Selecting Outdoor Unit
If there is no communicating outdoor unit, the screen, shown in Fig. 16, will appear. Press either Time or Temp +/- buttons to select AC (air conditioner), HP (heat pump), or None (no unit installed). Press
If either AC or HP has been selected as the outdoor unit type, the middle screen will appear (See Fig. 16). Press either Time or Temp +/- buttons to select appropriate Btu size of outdoor unit, then press right side button to continue. If a NIM (Network Interface Module) is applied for
