CE REQUIREMENTS

•This appliance must be installed in locations where it can be overseen by trained personnel.

•For proper operation, this appliance must be installed where the temperature is between 0°C to 35°C.

•Appliance shall not be tilted more than 10° for safe operation.

•An electrician must provide electrical service as specified in conformance with all local and national codes

•This appliance must not be cleaned by water jet.

•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instructions concern-

ing use of this appliance by a person responsible for its safety.

• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personel with a special cord available from the manufacturer or its authorized service personel in order to avoid a hazard.

INITIAL SET-UP

CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions.

1.Connect the dispenser to the power source and turn on the water supply.

2.The “HEATER” LED will glow for approximately five seconds. During this time, the electronic circuitry will check for a full tank of water.

3.If the tank is not full of water, the refill circuit will energize, indicated by the “REFILL” LED glowing. Water will automatically flow into the tank to the proper level and then shut off.

4.When the tank is full of water, the heater circuit will energize, indicated by the “HEATER” LED glowing inter- mittently until the proper temperature is achieved. A completely cold tank will take approximately twenty minutes for the water to heat.

5.The “READY” LED will glow when the proper water temperature is achieved.

NOTE - Stop dispensing if the “READY” LED is off. Dispense only when the ”READY” LED glows.

DRAINING THE DISPENSER

CAUTION - The dispenser must be disconnected from the power source throughout these steps.

1.Disconnect the dispenser from the power source.

2.Shut-off and disconnect the incoming water supply

3.Remove the small screws from the sides and front of the top panel.

4.Gently remove one of the grommets from the tank lid.

5.Insert a tube to the bottom of the tank and syphon ALL of the water out.

NOTE - The dispenser must be refilled using the INITIAL SET-UP steps before reconnecting to the power source.

CLEANING

The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment.

5

10889 021408

 

Page 4 Page 6
Page 5
Image 5
Bunn H10X manual CE Requirements, Initial SET-UP, Draining the Dispenser, Cleaning
Page 4 Page 6

H10X specifications

The Bunn H10X is a state-of-the-art coffee brewer designed for both commercial and high-demand home environments. Renowned for its reliability and superior performance, the H10X is engineered to deliver exceptional coffee quality while streamlining the brewing process.

One of the main features of the Bunn H10X is its capacity to brew large quantities of coffee efficiently. It boasts a 10-gallon tank, allowing it to produce up to 20 gallons of freshly brewed coffee in just one hour. This makes it an ideal choice for offices, cafes, and businesses that require a constant supply of coffee for their customers or employees.

The H10X is equipped with advanced brewing technology that ensures optimal extraction of flavor from coffee grounds. Its patented Pulse Brew feature enhances the brewing process by controlling the flow of water through the coffee grounds, enhancing flavor extraction and improving the overall taste profile. This technology is particularly beneficial for specialty coffees, where nuanced flavors are essential.

Additionally, the Bunn H10X incorporates a digital thermal control system, allowing users to adjust brewing temperatures for their specific coffee types. This precise control ensures that the coffee is brewed at the ideal temperature, maximizing flavor and aroma while minimizing bitterness. The machine also features a built-in water tank heater, providing consistent brewing temperatures throughout the day.

User-friendliness is another hallmark of the H10X. The intuitive interface includes programmable options for brewing strength and timing, enabling users to customize their coffee experience easily. An LCD display provides real-time updates on brewing status, making it simple to monitor the process.

Durability is a key characteristic of the Bunn H10X. Constructed from high-grade materials, this coffee brewer is built to withstand the demands of a bustling environment. Enhanced insulation keeps coffee hot for extended periods while reducing energy consumption.

For ease of maintenance, the H10X features a removable brew basket and a straightforward cleaning process. This design not only helps maintain the unit's performance but also extends its lifespan.

In summary, the Bunn H10X is a powerful, efficient, and user-friendly coffee brewer that stands out in the marketplace. With its impressive capacity, advanced brewing technologies, and robust construction, it is an ideal choice for anyone seeking a high-quality coffee solution.
Top Page Image Contents