INITIAL SETUP

CAUTION - The brewer must be disconnected from the power source throughout the initial setup, except when specified in the instructions.

1.Remove the top panel.

2.Rotate the control thermostat knob fully counterclockwise to the “OFF” position and replace the panel.

3.Insert an empty funnel into the funnel rails.

4.Place a decanter containing a small amount of water on the warmer beneath the funnel.

5.Connect the brewer to the power source, place the On/Off brew station warmer switch the upper position, and momentarily press the start switch. Water will begin flowing into the tank. When water stops flowing into the tank, initiate a second and a third brew cycle. During this third brew cycle the tank will fill to its capacity and the excess will flow from the sprayhead, out of the funnel, and into the decanter.

NOTE - The On/Off brew station warmer switch must be in the upper position to initiate and complete a brew cycle.

6.Place the On/Off brew station warmer switch in the lower position.

7.Disconnect the brewer from the power source.

8.Remove the top panel.

9.Rotate the control thermostat knob fully clock- wise to the “ON” position and replace the panel.

10.Connect the brewer to the power source and wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Some water will drip from the funnel during this time; this is due to expansion and should not occur thereafter.

11.Place an empty decanter under the funnel.

12.Place the On/Off brew station warmer switch in the upper position and momentarily press the start switch. Empty the decanter after water has stopped flowing from the funnel.

13.Allow the water in the tank to reheat to the proper temperature.

14.Place an empty decanter on the warmer and press the start switch. Check the water volume in the decanter after water has stopped flowing from the funnel. It should be 64 ounces.

15.If not, disconnect the brewer from the power source and remove the top panel.

P1712

16.Add or remove washers to the float on the level switch as required. Adding washers increases the volume, removing washers decreases it. Replace the top panel, connect the brewer to the power source, start, and measure another brew cycle.

17.Repeat steps 13-16 until 64 oz water volume is achieved.

P1478

Page 6

32430 051512

 

Page 5 Page 7
Page 6
Image 6
Bunn RL00006929 service manual Initial Setup, Repeat steps 13-16 until 64 oz water volume is achieved
Page 5 Page 7

RL00006929 specifications

The Bunn RL00006929 is a commercial-grade coffee brewer that exemplifies innovation, efficiency, and durability, making it a preferred choice for coffee shops, restaurants, and large offices. This model is designed to meet high-volume demands while ensuring consistent quality and flavor in every cup.

One of the most notable features of the Bunn RL00006929 is its capacity to brew up to 3.8 gallons of coffee per hour. This remarkable output is facilitated by its dual-funnel design, which allows for simultaneous brewing, reducing wait times and enhancing service speed. The brewer is equipped with a precise temperature control system, ensuring that water is heated to the optimal brewing temperature of 200°F. This consistency in temperature plays a crucial role in extracting the full flavor profile from coffee grounds.

In terms of design, the Bunn RL00006929 boasts a compact footprint, making it suitable for various settings, including kitchens with limited space. The unit features a stainless steel construction, which not only provides a sleek appearance but also contributes to its durability and resistance to corrosion. Additionally, the easy-access design makes maintenance straightforward, allowing operators to clean and service the unit with minimal effort.

The RL00006929 incorporates advanced technologies that enhance its functionality. For instance, the machine features a digital control panel that provides real-time feedback on brewing status, water temperature, and other critical parameters. This intelligent system allows operators to make quick adjustments and ensures that brewing conditions are always optimal.

Another standout characteristic is the integrated brew basket that holds filters securely in place, preventing spills and ensuring a smooth brewing process. This feature minimizes mess and simplifies the coffee-making process, making it user-friendly for both experienced baristas and novice operators.

In summary, the Bunn RL00006929 stands out for its high brewing capacity, precise temperature control, compact design, and user-friendly features. Its combination of advanced technology and durability makes it an excellent investment for any establishment that demands quality coffee at high volumes. With Bunn's reputation for excellence, the RL00006929 is a reliable choice for delivering exceptional coffee experiences.
Top Page Image Contents