Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 6000 manual Installation, Required Tools, UNPACKING THE 6E233-49 SMARTSWITCH

Models: 6000

1 58

Download 58 pages 35.45 Kb

Page 31

Installation

3

Installation

Only qualified personnel should install the 6E233-49 SmartSwitch.

Important Notice

Depending on the firmware version used in the SmartSwitch, some features described in this document may not be supported. Refer to the Release Notes shipped with the SmartSwitch to determine which features are supported.

This chapter provides the instructions required to install the 6E233-49 SmartSwitch. Follow the order of the sections listed below to ensure a proper installation:

•Required tools (Section 3.1)

•Unpacking the 6E233-49 SmartSwitch (Section 3.2)

•Installing Options (Section 3.3)

•Installing the 6E233-49 SmartSwitch in the 6C105 chassis (Section 3.4)

•Connecting to the network (Section 3.5)

3.1REQUIRED TOOLS

A Phillips screwdriver is required to install the HSIMs in the 6E233-49.

3.2UNPACKING THE 6E233-49 SMARTSWITCH

1.Open the box and remove the packing material protecting the module.

2.Verify the contents of the carton as listed in Table 3-1.

Installation 3-1

Image 31

Cabletron Systems 6000 manual Installation, Required Tools, UNPACKING THE 6E233-49 SMARTSWITCH, Important Notice

Contents

6E233-49Title Page SmartSwitch Interface Module User’s GuideRESET 9033379Page Only qualified personnel should perform installation procedures INDUSTRY CANADA NOTICE FCC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC PROGRAM LICENSE AGREEMENT Page CABLETRON SYSTEMS SALES AND SERVICE, INC PROGRAM LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU EUROPE MIDDLE EAST AFRICA ASIA AUSTRALIA PACIFIC RIM CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENTviii If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to i reexport or release the Program, the source code for the Program or technology to a national of a country in Country Groups D1 or E2 Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be designated by the United States Government, ii export to Country Groups D1 or E2 as defined herein the direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List, or iii if the direct product of the technology is a complete plant o r any major component of a plant, export to Country Groups D1 or E2 the direct product of the plant or a major component thereof, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions ListSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS CLASS 1 LASER TRANSCEIVERSSAFETY INFORMATION READ THE FOLLOWING SAFETY INFORMATION BEFORE INSTALLING OR OPERATINGBerkshire RG14 2PZ, England DECLARATION OF CONFORMITY73/23/EEC Manufacturer’s Name Cabletron Systems, Inc Rochester, NHxiii ContentsINTRODUCTION FiguresOPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS INSTALLATIONTROUBLESHOOTING SPECIFICATIONSxiii FiguresPage TablesAbout This Guide USING THIS GUIDEImportant Notice STRUCTURE OF THIS GUIDE RELATED DOCUMENTS DOCUMENT CONVENTIONS 1.1 OVERVIEW IntroductionImportant Notice 1-2 Introduction Figure 1-1 The 6E233-49 SmartSwitchRESET Button RESET OverviewThe module will reboot after RAD is successful 1.1.1 Connectivity1.1.2 Auto-Negotiation 1.1.3 Runtime IP Address Discovery1.1.7 Broadcast Suppression 1.1.4 Full Duplex Switched Ethernet1.1.5 SmartTrunk 1.1.6 Remote Monitoring RMON1.1.9 Rate Limiting 1.1.8 Port/VLAN Redirect FunctionsManagement User’s Guide 1.1.12 Management 1.1.10 GARP Switch Operation1.1.13 Switching Options 1.1.11 802.1 Port Priority1.1.16 Standards Compatibility 1.1.17 LANVIEW Diagnostic LEDs1.1.14 Distributed Chassis Management 1.1.15 Optional HSIMs1.2 GETTING HELP 2.1 SmartTrunk Network Requirements2.2 10BASE-T NETWORK Page Important Notice Installation3.2 UNPACKING THE 6E233-49 SMARTSWITCH 3.1 REQUIRED TOOLS3.4 INSTALLING THE 6E233-49 SMARTSWITCH INTO THE 6C105 CHASSIS 3.3 INSTALLING OPTIONS3. Locate the antistatic wrist strap shipped with the 6C105 chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105 Connector Installing the 6E233-49 SmartSwitch into the 6C105 ChassisFigure 3-1 Installing an Interface Module 3-4 Installation3.5 CONNECTING TO THE NETWORK Figure 3-2 Straight Cable Connection Connecting to the Network3-6 Installation RESETFigure 3-3 Connection Using the RJ21 Angle Adapter Screw RJ21Clip Adapter/Extender RJ21 Right-Angled ConnectorClip Screw 3.6 COMPLETING THE INSTALLATION 4.1 USING LANVIEW TroubleshootingFigure 4-1 LANVIEW LEDs Using LANVIEW4-2 Troubleshooting RESETFlashing indicates an irregular LED pulse Table 4-1 LANVIEW LEDs CPU, Receive, and Transmit Status Continued Refer to the Local Management4.2 TROUBLESHOOTING CHECKLIST Loss of power to the Table 4-4 Firmware Troubleshooting Refer to the Local Management User’s Guide for setupRefer to the Local Management User’s Guide on Refer to the Local Management User’s Guide for Enable port. Refer to the Local Management User’s GuideRefer to the Local Management User’s Guide for IP Table 4-6 Device Setup Troubleshooting 4.3 USING THE RESET BUTTON A.3 ENVIRONMENTAL REQUIREMENTS SpecificationsA.1 MODULE SPECIFICATIONS A.2 PHYSICAL PROPERTIESSlot accepts optional HSIMs that provide a variety of A.4 INPUT/OUTPUT PORTSA.5 COM PORT PINOUT ASSIGNMENTS A.6 REGULATORY COMPLIANCEB.2 SETTING THE MODE SWITCHES Optional Installations and Mode Switch Bank SettingsB.1 REQUIRED TOOLS Switch definitions and positions are as follows B.3.1 Locating SIMMs B.3 SIMM UPGRADEB.3.2 Installing the DRAM SIMM Optional Installations and Mode Switch Bank Settings B.4 INSTALLING OPTIONAL HIGH SPEED INTERFACE MODULESHSIM Connector Installing Optional High Speed Interface ModulesPage Numerics IndexIndex-2