Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 6000 manual

Models: 6000

1 58

Download 58 pages 35.45 Kb

Page 33

3.Locate the antistatic wrist strap shipped with the 6C105 chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105.

Installing the 6E233-49 SmartSwitch into the 6C105 Chassis

3.Locate the antistatic wrist strap shipped with the 6C105 chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105.

4.Remove the module from the plastic bag. (Save the bag in the event the module must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD).

5.Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact Cabletron Systems. Refer to Section 1.2.

To prevent damaging the backplane connectors in the following step, take care that the

!module slides in straight and properly engages the backplane connectors.

CAUTION

NOTE

In the following step, ensure that the top plastic locking tab lines up with the desired slot number located on the front panel of the chassis. Refer to Figure 3-1.

6.Locate the slot guides that line up with the number of the slot in which the module will be installed. Install the module in the chassis by aligning the module circuit card between the upper and lower metal rail guides of the desired slot, sliding it into the chassis, and locking down the top and bottom plastic locking tabs, as shown in Figure 3-1. Take care that the module slides in straight and properly engages the backplane connectors.

7.If the chassis in which the module is installed was powered down for the installation, turn it back on. Check to see that the CPU LED settles at solid green after a few minutes. If the LED does not turn solid green, refer to Chapter 4 for details.

Installation 3-3

Image 33

Cabletron Systems 6000 manual

Contents

RESET SmartSwitch Interface Module User’s Guide9033379 6E233-49Title PagePage Only qualified personnel should perform installation procedures FCC NOTICE INDUSTRY CANADA NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC PROGRAM LICENSE AGREEMENT Page CABLETRON SYSTEMS SALES AND SERVICE, INC PROGRAM LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU EUROPE MIDDLE EAST AFRICA ASIA AUSTRALIA PACIFIC RIM CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENTviii If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to i reexport or release the Program, the source code for the Program or technology to a national of a country in Country Groups D1 or E2 Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be designated by the United States Government, ii export to Country Groups D1 or E2 as defined herein the direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List, or iii if the direct product of the technology is a complete plant o r any major component of a plant, export to Country Groups D1 or E2 the direct product of the plant or a major component thereof, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions ListSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSREAD THE FOLLOWING SAFETY INFORMATION BEFORE INSTALLING OR OPERATING SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS73/23/EEC Manufacturer’s Name Cabletron Systems, Inc DECLARATION OF CONFORMITYRochester, NH Berkshire RG14 2PZ, EnglandINTRODUCTION ContentsFigures xiiiTROUBLESHOOTING INSTALLATIONSPECIFICATIONS OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGSxiii FiguresPage TablesUSING THIS GUIDE About This GuideImportant Notice STRUCTURE OF THIS GUIDE RELATED DOCUMENTS DOCUMENT CONVENTIONS Introduction 1.1 OVERVIEWImportant Notice RESET Button RESET Figure 1-1 The 6E233-49 SmartSwitchOverview 1-2 Introduction1.1.2 Auto-Negotiation 1.1.1 Connectivity1.1.3 Runtime IP Address Discovery The module will reboot after RAD is successful1.1.5 SmartTrunk 1.1.4 Full Duplex Switched Ethernet1.1.6 Remote Monitoring RMON 1.1.7 Broadcast Suppression1.1.8 Port/VLAN Redirect Functions 1.1.9 Rate LimitingManagement User’s Guide 1.1.13 Switching Options 1.1.10 GARP Switch Operation1.1.11 802.1 Port Priority 1.1.12 Management1.1.14 Distributed Chassis Management 1.1.17 LANVIEW Diagnostic LEDs1.1.15 Optional HSIMs 1.1.16 Standards Compatibility1.2 GETTING HELP Network Requirements 2.1 SmartTrunk2.2 10BASE-T NETWORK Page 3.2 UNPACKING THE 6E233-49 SMARTSWITCH Installation3.1 REQUIRED TOOLS Important Notice3.4 INSTALLING THE 6E233-49 SMARTSWITCH INTO THE 6C105 CHASSIS 3.3 INSTALLING OPTIONS3. Locate the antistatic wrist strap shipped with the 6C105 chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105 Figure 3-1 Installing an Interface Module Installing the 6E233-49 SmartSwitch into the 6C105 Chassis3-4 Installation Connector3.5 CONNECTING TO THE NETWORK 3-6 Installation Connecting to the NetworkRESET Figure 3-2 Straight Cable ConnectionScrew RJ21Clip Adapter/Extender RJ21 Right-Angled Connector Figure 3-3 Connection Using the RJ21 Angle AdapterClip Screw 3.6 COMPLETING THE INSTALLATION 4.1 USING LANVIEW Troubleshooting4-2 Troubleshooting Using LANVIEWRESET Figure 4-1 LANVIEW LEDsFlashing indicates an irregular LED pulse Table 4-1 LANVIEW LEDs CPU, Receive, and Transmit Status Continued Refer to the Local Management4.2 TROUBLESHOOTING CHECKLIST Loss of power to the Refer to the Local Management User’s Guide for setup Table 4-4 Firmware TroubleshootingRefer to the Local Management User’s Guide on Enable port. Refer to the Local Management User’s Guide Refer to the Local Management User’s Guide forRefer to the Local Management User’s Guide for IP Table 4-6 Device Setup Troubleshooting 4.3 USING THE RESET BUTTON A.1 MODULE SPECIFICATIONS SpecificationsA.2 PHYSICAL PROPERTIES A.3 ENVIRONMENTAL REQUIREMENTSA.5 COM PORT PINOUT ASSIGNMENTS A.4 INPUT/OUTPUT PORTSA.6 REGULATORY COMPLIANCE Slot accepts optional HSIMs that provide a variety ofOptional Installations and Mode Switch Bank Settings B.2 SETTING THE MODE SWITCHESB.1 REQUIRED TOOLS Switch definitions and positions are as follows B.3.1 Locating SIMMs B.3 SIMM UPGRADEB.3.2 Installing the DRAM SIMM HSIM Connector B.4 INSTALLING OPTIONAL HIGH SPEED INTERFACE MODULESInstalling Optional High Speed Interface Modules Optional Installations and Mode Switch Bank SettingsPage Numerics IndexIndex-2