SmartSwitch Interface Module User’s Guide
RESET
9033379
6E233-49Title Page
Page
Only qualified personnel should perform installation procedures
INDUSTRY CANADA NOTICE
FCC NOTICE
VCCI NOTICE
CABLETRON SYSTEMS, INC PROGRAM LICENSE AGREEMENT
Page
CABLETRON SYSTEMS SALES AND SERVICE, INC PROGRAM LICENSE AGREEMENT
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU
CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENT
EUROPE MIDDLE EAST AFRICA ASIA AUSTRALIA PACIFIC RIM
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to i reexport or release the Program, the source code for the Program or technology to a national of a country in Country Groups D1 or E2 Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be designated by the United States Government, ii export to Country Groups D1 or E2 as defined herein the direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List, or iii if the direct product of the technology is a complete plant o r any major component of a plant, export to Country Groups D1 or E2 the direct product of the plant or a major component thereof, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List
viii
CLASS 1 LASER TRANSCEIVERS
SAFETY INFORMATION
READ THE FOLLOWING SAFETY INFORMATION BEFORE INSTALLING OR OPERATING
SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS
DECLARATION OF CONFORMITY
73/23/EEC Manufacturer’s Name Cabletron Systems, Inc
Rochester, NH
Berkshire RG14 2PZ, England
Contents
INTRODUCTION
Figures
xiii
INSTALLATION
TROUBLESHOOTING
SPECIFICATIONS
OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS
Figures
xiii
Tables
Page
About This Guide
USING THIS GUIDE
Important Notice
STRUCTURE OF THIS GUIDE
RELATED DOCUMENTS
DOCUMENT CONVENTIONS
1.1 OVERVIEW
Introduction
Important Notice
Figure 1-1 The 6E233-49 SmartSwitch
RESET Button RESET
Overview
1-2 Introduction
1.1.1 Connectivity
1.1.2 Auto-Negotiation
1.1.3 Runtime IP Address Discovery
The module will reboot after RAD is successful
1.1.4 Full Duplex Switched Ethernet
1.1.5 SmartTrunk
1.1.6 Remote Monitoring RMON
1.1.7 Broadcast Suppression
1.1.9 Rate Limiting
1.1.8 Port/VLAN Redirect Functions
Management User’s Guide
1.1.10 GARP Switch Operation
1.1.13 Switching Options
1.1.11 802.1 Port Priority
1.1.12 Management
1.1.17 LANVIEW Diagnostic LEDs
1.1.14 Distributed Chassis Management
1.1.15 Optional HSIMs
1.1.16 Standards Compatibility
1.2 GETTING HELP
2.1 SmartTrunk
Network Requirements
2.2 10BASE-T NETWORK
Page
Installation
3.2 UNPACKING THE 6E233-49 SMARTSWITCH
3.1 REQUIRED TOOLS
Important Notice
3.3 INSTALLING OPTIONS
3.4 INSTALLING THE 6E233-49 SMARTSWITCH INTO THE 6C105 CHASSIS
3. Locate the antistatic wrist strap shipped with the 6C105 chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105
Installing the 6E233-49 SmartSwitch into the 6C105 Chassis
Figure 3-1 Installing an Interface Module
3-4 Installation
Connector
3.5 CONNECTING TO THE NETWORK
Connecting to the Network
3-6 Installation
RESET
Figure 3-2 Straight Cable Connection
Figure 3-3 Connection Using the RJ21 Angle Adapter
Screw RJ21Clip Adapter/Extender RJ21 Right-Angled Connector
Clip Screw
3.6 COMPLETING THE INSTALLATION
Troubleshooting
4.1 USING LANVIEW
Using LANVIEW
4-2 Troubleshooting
RESET
Figure 4-1 LANVIEW LEDs
Flashing indicates an irregular LED pulse
Refer to the Local Management
Table 4-1 LANVIEW LEDs CPU, Receive, and Transmit Status Continued
4.2 TROUBLESHOOTING CHECKLIST
Loss of power to the
Table 4-4 Firmware Troubleshooting
Refer to the Local Management User’s Guide for setup
Refer to the Local Management User’s Guide on
Refer to the Local Management User’s Guide for
Enable port. Refer to the Local Management User’s Guide
Refer to the Local Management User’s Guide for IP
Table 4-6 Device Setup Troubleshooting
4.3 USING THE RESET BUTTON
Specifications
A.1 MODULE SPECIFICATIONS
A.2 PHYSICAL PROPERTIES
A.3 ENVIRONMENTAL REQUIREMENTS
A.4 INPUT/OUTPUT PORTS
A.5 COM PORT PINOUT ASSIGNMENTS
A.6 REGULATORY COMPLIANCE
Slot accepts optional HSIMs that provide a variety of
B.2 SETTING THE MODE SWITCHES
Optional Installations and Mode Switch Bank Settings
B.1 REQUIRED TOOLS
Switch definitions and positions are as follows
B.3 SIMM UPGRADE
B.3.1 Locating SIMMs
B.3.2 Installing the DRAM SIMM
B.4 INSTALLING OPTIONAL HIGH SPEED INTERFACE MODULES
HSIM Connector
Installing Optional High Speed Interface Modules
Optional Installations and Mode Switch Bank Settings
Page
Index
Numerics
Index-2
