Manuals / Cabletron Systems / Computer Equipment / Network Card

Cabletron Systems 9F125-0, 9F120-08 The Reset Switch, Cabling Requirements, 10BASE-FL Network

Models: 9F125-0 9F122-12 9F120-08

1 36

Download 36 pages 733 b

Page 26

The Reset Switch

Installing the SmartSwitch 9000 Module

The Reset Switch

The Reset switch is located under the top plastic tab as shown in Figure 2-3.

Use the reset switch to reset the module’s processor, shutdown (power down) the module, and/or restart the module.

•To reset the module’s i960 processor, press the reset switch twice within three seconds.

•To shut down the module, press and hold the reset switch for three or more seconds.

•To restart the module, press the reset switch momentarily.

SNMP management may be used to disable this switch to enhance module security.

Reset Switch

SMB CPU

Figure 2-3. The Reset Switch

Cabling Requirements

10BASE-FL Network

The 9E531-24 supports 10BASE-FL Ethernet specifications. When connecting a 10BASE-FL segment to any of the front panel ports, ensure that the network meets the optical performance requirements for the 10BASE-FL 802.3 standard.

The 9E531-24 supports multimode fiber cables at the 850nm wavelength, at lengths up to 2 km.

2-6

Image 26

Cabletron Systems 9F125-0, 9F120-08, 9F122-12 manual The Reset Switch, Cabling Requirements, 10BASE-FL Network

Contents

SmartSwitch 9E531-24 24 Port 10BASE-FL Ethernet Module User’s Guide 9033274Page VCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CABLETRON SYSTEMS, INC PROGRAM LICENSE AGREEMENT CABLETRON SYSTEMS SALES AND SERVICE, INC PROGRAM LICENSE AGREEMENT CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENT 4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party INSTALLING OR OPERATING THESE MODULES SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSREAD THE FOLLOWING SAFETY INFORMATION BEFORE SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSDECLARATION OF CONFORMITY viii Chapter ContentsSpecifications IntroductionWeight ContentsDimensions EnvironmentChapter FeaturesIntroduction 9E531-24 IntroductionFigure 1-1. The 9E531-24 ETHERNETAll purchased bandwidth is used Remote Monitoring RMON ManagementWebView Broadcast SuppressionThe 9E531-24 supports the following two types of flow control Standards Compatibility GARP Switch OperationLANVIEW Diagnostic LEDs Year 2000 ComplianceRelated Manuals Getting Help Unpacking the Module Installing the SmartSwitch 9000 ModuleUser Accessible Components ChapterInstalling the SmartSwitch 9000 Module Figure 2-1. User-Accessible ComponentsFunction SwitchSee the Cautions at the end of this table DescriptionInstalling the Module into the SmartSwitch 9000 Chassis Using DIP Switch4. Lock down the top and bottom plastic tabs, as shown in Figure 10BASE-FL Network The Reset SwitchCabling Requirements Chapter SmartSwitch ArchitectureTechnical Overview Technical Overview System Management BusesFigure 3-1. Block Diagram SMB-1 Bus System Diagnostic ControllerDC/DC Converter SMB-10 BusINB Interface i960 CoreINB Receive LANVIEW LEDsChapter System Status INB TransmitState LANVIEW LEDsLED Color DescriptionState LANVIEW LEDsColor LED ColorLANVIEW LEDs Chapter SpecificationsTechnical Specifications Physical ServiceRegulatory Compliance