Manuals / Cabletron Systems / Computer Equipment / Network Card

Cabletron Systems 9F125-0, 9F120-08, 9F122-12 manual LANVIEW LEDs, LED Color, State, Description

Models: 9F125-0 9F122-12 9F120-08

1 36

Download 36 pages 733 b

Page 32

LANVIEW LEDs

The functions of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in Table 4-1.

Table 4-1. System Status (SMB and CPU) LEDs

LED Color	State	Description


Green	Functional	Fully operational

Yellow	Testing	Power-up testing

Yellow (Flashing)	Crippled	Not fully operational (e.g., one bad port)

Yellow/Green	Booting	Blinks yellow and green while booting

Red	Reset	Normal power-up reset

Red (Flashing)	Failed	Fatal error has occurred

Off	Power off	Module powered off

The functions of the INB transmit LED are listed in Table 4-2.

	Table 4-2. INB Transmit LED

LED Color	State


Green (Flashing)	Data activity

Yellow (Flashing)	Port in standby state

Red (Flashing)	Collision

Red	Fault

Off	No activity, Port disabled

The functions of the INB receive LED are listed in Table 4-3.

	Table 4-3. INB Receive LED

LED Color	State


Green (Flashing)	Link, Port disabled

Green	Link, Port enabled, No activity

Yellow (Flashing)	Link, Port enabled, Activity

Red	Fault

Off	No Link

4-2

Image 32

Cabletron Systems 9F125-0, 9F120-08, 9F122-12 manual LANVIEW LEDs, LED Color, State, Description

Contents

SmartSwitch 9E531-24 24 Port 10BASE-FL Ethernet Module User’s Guide 9033274Page VCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CABLETRON SYSTEMS, INC PROGRAM LICENSE AGREEMENT CABLETRON SYSTEMS SALES AND SERVICE, INC PROGRAM LICENSE AGREEMENT CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENT 4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS READ THE FOLLOWING SAFETY INFORMATION BEFOREINSTALLING OR OPERATING THESE MODULES SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSDECLARATION OF CONFORMITY viii Contents SpecificationsChapter IntroductionContents DimensionsWeight EnvironmentChapter FeaturesIntroduction Introduction Figure 1-1. The 9E531-249E531-24 ETHERNETAll purchased bandwidth is used Management WebViewRemote Monitoring RMON Broadcast SuppressionThe 9E531-24 supports the following two types of flow control GARP Switch Operation LANVIEW Diagnostic LEDsStandards Compatibility Year 2000 ComplianceRelated Manuals Getting Help Installing the SmartSwitch 9000 Module User Accessible ComponentsUnpacking the Module ChapterInstalling the SmartSwitch 9000 Module Figure 2-1. User-Accessible ComponentsSwitch See the Cautions at the end of this tableFunction DescriptionInstalling the Module into the SmartSwitch 9000 Chassis Using DIP Switch4. Lock down the top and bottom plastic tabs, as shown in Figure 10BASE-FL Network The Reset SwitchCabling Requirements Chapter SmartSwitch ArchitectureTechnical Overview Technical Overview System Management BusesFigure 3-1. Block Diagram System Diagnostic Controller DC/DC ConverterSMB-1 Bus SMB-10 BusINB Interface i960 CoreLANVIEW LEDs ChapterINB Receive System Status INB TransmitLANVIEW LEDs LED ColorState DescriptionLANVIEW LEDs ColorState LED ColorLANVIEW LEDs Chapter SpecificationsTechnical Specifications Physical ServiceRegulatory Compliance