Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems CSX200 manual Port Descriptions, 1 Ethernet Twisted Pair Ports

Models: CSX200

1 88

Download 88 pages 62.16 Kb

Page 32

Chapter 3: 10BASE-T LAN Requirements

Temperature — Multi-pair PVC 24 AWG telephone cable typically has an attenuation of approximately 8–10dB/100 m at 20°C (68°F). The attenuation of PVC insulated cable varies with temperature. At temperatures greater than 40°C (104°F), use plenum-rated cable to ensure that attenuation remains within speciﬁcation.

Port Descriptions

Table 3-1deﬁnes the pinout for the Ethernet twisted pair ports 1 through 12.

Table 3-1 Ethernet Twisted Pair Ports (1-12)

	Pin Number	Signal Name


	1	Twisted Pair
	1	Transmit +
		Transmit +

	2	Twisted Pair
	2	Transmit -
		Transmit -

	3	Twisted Pair
	3	Receive +
		Receive +

	4	Ground

	5	Ground

	6	Twisted Pair
	6	Receive -
		Receive -

	7	Ground

	8	Ground

3-2	CSX200 Installation Guide

Image 32

Cabletron Systems CSX200 manual Port Descriptions, 1 Ethernet Twisted Pair Ports

Contents

CSX200 CyberSWITCH Installation Guide 9032753Page CSX200 Installation Guide FCC NoticeIndustry Canada Notice VCCI Notice Cabletron Systems, Inc. Program License AgreementCabletron Software Program License CSX200 Installation GuideCSX200 Installation Guide Exclusion of Warranty and Disclaimer of LiabilityUnited States Government Restricted Rights Declaration of Conformity CSX200 Installation GuideContents CSX200 Installation GuideCHAPTER 1 INTRODUCTION CHAPTER 2 ABOUT THE CSX200Contents INSTALLATIONTROUBLESHOOTING CSX200 Installation GuideCSX200 Installation Guide APPENDIX A WPIM CABLE SPECIFICATIONSAPPENDIX B SPECIFICATIONS AND STANDARDS COMPLIANCE Contents CSX200 Installation GuideAPPENDIX C FCC PART 68 - USER’S INFORMATION FOR CSX200 APPENDIX D GLOSSARYRelated Documentation How to Use This Guide1 Introduction Appendix D, Glossary, deﬁnes commonly used networking terms Document Conventions CSX200 Installation GuideThe following conventions are used throughout this guide Document ConventionsGetting Help WAN Connection 2 About the CSX200CSX200 Hardware Ethernet LAN Connection Remote Management Capabilities Optional FeaturesRemote Management Capabilities WAN Protocols CSX200 Firmware SupportIEEE 802.3 Ethernet Firmware Data Compression HDLCDHCP and NAT CSX200 Firmware SupportFrame Relay Protocol Point-to-Point Protocol PPP PAP and CHAP SecurityMultilink Protocol ISDNHDSL Bridging and RoutingIn transparent bridging, the decision to forward the frame is based on this comparison. If the address indicates that the sending station and the destination station are on the same side of the bridge, the frame is not forwarded across the bridge. If the addresses do not indicate that, the bridge forwards the broadcast frame across the bridge to the other networks Bridging and Routing Protocol Filtering System Passwords Simple Network Management Protocol SNMPFrame Relay DTE MIB RFC1490 Security MIB RFC1472 CCP, PAP, and CHAP IP Events, continued IP has detected Link UP on interface # Software and Firmware Upgrades 2-16 CSX200 Installation GuideChapter 2 About the CSX200 10BASE-T Twisted Pair Network 10BASE-T LAN RequirementsNetwork Requirements Port Descriptions Table 3-1 Ethernet Twisted Pair PortsConnecting UTP Cables to Ports 1 Through 10BASE-T LAN Conﬁguration4. Repeat step 2, above, until all connections have been made Unpacking the CSX200 4 InstallationInstallation Guidelines Removing the CSX200 Cover Installing a WPIM Installation Guidelinessection, Tabletop and Shelf Installations on page 4-6, are met CSX200 Installation GuideTo install a WPIM, follow these instructions COMP/ENCR Module Installation Installing the CSX200 Tabletop and Shelf InstallationsRackmount Installation Installing the CSX200 in a 19-inch rackConnecting the CSX200 to a power source Rack mounting the CSX200 requires the following stepsAttaching the Strain-Relief Bracket Attaching the Rackmount Brackets Rackmount Brackets ScrewsPowering the CSX200 Installing the CSX200 in a 19-Inch Rack5 Troubleshooting Chapter 5 Troubleshooting CSX200 Installation GuideTable 5-2 CSX200 LAN LED States Table 5-3 CSX200 WAN LED StatesTroubleshooting CSX200 Installation GuideTable 5-4 CSX200 WAN LED States for STS Table 5-5 CSX200 WAN LED States for STSTroubleshooting CSX200 Hardware Troubleshooting the LANPower PWR LED is OFF Processor CPU LED is OFFTroubleshooting the WAN Link LNK LED is REDLink LNK LED is AMBER Status 1 STS1 LED is OFFStatus 1 STS1 LED is RED WPIM-SYNC Installed in CSX200WPIM-HDSL Installed in CSX200 WPIM-T1, WPIM-E1, or WPIM-DI Installed in CSX200 is in RED Alarm ModeStatus 1 STS1 LED is AMBER Status 1 STS1 LED is GREENStatus 2 STS 2 LED is RED WPIM-HDSL Installed in CSX200 Status 2 STS2 LED is OFFWPIM-HDSL is installed in CSX200 WPIM-T1, WPIM-E1, WPIM-DI, or WPIM-DDS Installed in CSX200Status 2 STS2 LED is AMBER Status 2 STS2 LED is GREENInvestigating Software Conﬁguration Problems Test TST LED is AMBER blinkingConnection to Device Fails During Software Conﬁguration User Cannot Communicate with Remote Network StationCheck that TCP/IP Routing is set on and is enabled at the remote end 5-12 Chapter 5 TroubleshootingCSX200 Installation Guide CSX200 Installation Guide A WPIM Cable SpeciﬁcationsWPIM-T1 Appendix A WPIM Cable Specifications CSX200 Installation GuideTable A-3 provides RJ48 DTE pin assignments Table A-4 provides RJ48 network pin assignmentsWPIM-SY WPIM-SYEIA-449 Appendix A WPIM Cable SpecificationsCSX200 Installation Guide Table A-7 provides pin assignments for the EIA-449 interface cableV.35 CSX200 Installation GuideTable A-9 provides pin assignments for the V.35 interface cable WPIM-SYTable A-9 V.35 Interface Cable Pin Assignment Continued Appendix A WPIM Cable SpecificationsCSX200 Installation Guide EIA-232 CSX200 Installation GuideTable A-11 provides pin assignments for the EIA-232 interface cable WPIM-SYX.21 Appendix A WPIM Cable SpecificationsCSX200 Installation Guide Table A-13 provides pin assignments for the X.21 interface cableEIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 A ALT A Appendix A WPIM Cable Specifications CSX200 Installation GuideA-10 a ACWPIM-DDS WPIM-DDSWPIM-E1 CSX200 Installation Guide Table A-20 provides WPIM-E1 DTE interface cable pin assignmentsWPIM-E1 A-13Table A-23 WPIM-DI Network WPIM-DITable A-22 WPIM-DI Connector Information WPIM-HDSL WPIM-HDSLA-16 Appendix A WPIM Cable SpecificationsCSX200 Installation Guide Table B-1 Hardware Specifications B Speciﬁcations and Standards ComplianceCSX200 Installation Guide WPIM-T1 CSX200 Regulatory ComplianceIndividual WPIM Regulatory Compliance Individual WPIM Regulatory Compliance WPIM-SYWPIM-DDS WPIM-HDSL WPIM-E1WPIM-DI Table C-2 WPIM-DDS Only C FCC Part 68 - User’s Information for CSX200Table C-1 WPIM-DI and WPIM-T1 6. If the telephone company alters their equipment in a manner that will affect use of this device, they must give you advance warning so as to give you the opportunity for uninterrupted service. You will be advised of your right to file a complaint with the FCC For the work to be performed in the certiﬁed territory of the control of a supervisor trained in accordance with D Glossary EtherTalk - AppleTalk protocols running on Ethernet Glossary RJ11 - Standard 4-wire connectors for telephone lines SNMP - Simple Network Management Protocol. A widely implemented Internet network management protocol that allows status monitoring, getting/setting of parameters for conﬁguration and control of network devices, such as routers and bridges Watchdog Frames - Frames sent out by servers to clients, under IPX, to verify that clients are still logged on Index NumericsIndex-2 CSX200 Installation GuideIndex