Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems manual A WPIM Cable Speciﬁcations, WPIM-T1, CSX200 Installation Guide

Models: CSX200

1 88

Download 88 pages 62.16 Kb

Page 57

A WPIM Cable Speciﬁcations

A WPIM Cable Speciﬁcations

NOTE

For all WPIM cables, there is part number information for ordering a standard 20-foot cable or a speciﬁed length of cable. The number 20 followed by the part number denotes the standard 20-foot cable. The letter “L” denotes the speciﬁed length required in feet or meters. For example: 9372095-3 denotes a 3 foot cable; 9372095-3M denotes a 3-meter cable.

WPIM-T1

This section provides the Cabletron Systems part number and connector speciﬁcations for WPIM-T1 interface cables.

Table A-1provides connector type and part number information.

Table A-1 T-1 Interface Cable Part Numbers

Connector Type

Part Number

RJ48C

9372094

Table A-2provides RJ48 connector pin assignments.

Table A-2 T-1 Connector Pin Assignments

Pin	Signal


1	Receive Ring

2	Receive Tip

3	Not Used

4	Transmit Ring

5	Transmit Tip

6	Not Used

7	Shield Ground

8	Shield Ground

CSX200 Installation Guide

A-1

Image 57

Cabletron Systems manual A WPIM Cable Speciﬁcations, WPIM-T1, CSX200 Installation Guide

Contents

9032753 CSX200 CyberSWITCH Installation GuidePage FCC Notice Industry Canada NoticeCSX200 Installation Guide Cabletron Systems, Inc. Program License Agreement VCCI NoticeCabletron Software Program License CSX200 Installation GuideExclusion of Warranty and Disclaimer of Liability United States Government Restricted RightsCSX200 Installation Guide CSX200 Installation Guide Declaration of ConformityCSX200 Installation Guide ContentsCHAPTER 1 INTRODUCTION CHAPTER 2 ABOUT THE CSX200INSTALLATION ContentsTROUBLESHOOTING CSX200 Installation GuideAPPENDIX A WPIM CABLE SPECIFICATIONS APPENDIX B SPECIFICATIONS AND STANDARDS COMPLIANCECSX200 Installation Guide CSX200 Installation Guide ContentsAPPENDIX C FCC PART 68 - USER’S INFORMATION FOR CSX200 APPENDIX D GLOSSARYHow to Use This Guide 1 IntroductionRelated Documentation Appendix D, Glossary, deﬁnes commonly used networking terms CSX200 Installation Guide Document ConventionsThe following conventions are used throughout this guide Document ConventionsGetting Help 2 About the CSX200 CSX200 HardwareWAN Connection Ethernet LAN Connection Optional Features Remote Management CapabilitiesRemote Management Capabilities CSX200 Firmware Support IEEE 802.3 EthernetWAN Protocols HDLC Firmware Data CompressionDHCP and NAT CSX200 Firmware SupportFrame Relay Protocol PAP and CHAP Security Point-to-Point Protocol PPPISDN Multilink ProtocolBridging and Routing HDSLIn transparent bridging, the decision to forward the frame is based on this comparison. If the address indicates that the sending station and the destination station are on the same side of the bridge, the frame is not forwarded across the bridge. If the addresses do not indicate that, the bridge forwards the broadcast frame across the bridge to the other networks Bridging and Routing Protocol Filtering Simple Network Management Protocol SNMP System PasswordsFrame Relay DTE MIB RFC1490 Security MIB RFC1472 CCP, PAP, and CHAP IP Events, continued IP has detected Link UP on interface # Software and Firmware Upgrades CSX200 Installation Guide Chapter 2 About the CSX2002-16 10BASE-T LAN Requirements Network Requirements10BASE-T Twisted Pair Network Table 3-1 Ethernet Twisted Pair Ports Port Descriptions10BASE-T LAN Conﬁguration Connecting UTP Cables to Ports 1 Through4. Repeat step 2, above, until all connections have been made 4 Installation Installation GuidelinesUnpacking the CSX200 Removing the CSX200 Cover Installation Guidelines Installing a WPIMsection, Tabletop and Shelf Installations on page 4-6, are met CSX200 Installation GuideTo install a WPIM, follow these instructions COMP/ENCR Module Installation Tabletop and Shelf Installations Installing the CSX200Installing the CSX200 in a 19-inch rack Rackmount InstallationConnecting the CSX200 to a power source Rack mounting the CSX200 requires the following stepsAttaching the Strain-Relief Bracket Rackmount Brackets Screws Attaching the Rackmount BracketsInstalling the CSX200 in a 19-Inch Rack Powering the CSX2005 Troubleshooting CSX200 Installation Guide Chapter 5 TroubleshootingTable 5-2 CSX200 LAN LED States Table 5-3 CSX200 WAN LED StatesCSX200 Installation Guide TroubleshootingTable 5-4 CSX200 WAN LED States for STS Table 5-5 CSX200 WAN LED States for STSTroubleshooting the LAN Troubleshooting CSX200 HardwarePower PWR LED is OFF Processor CPU LED is OFFLink LNK LED is RED Troubleshooting the WANLink LNK LED is AMBER Status 1 STS1 LED is OFFWPIM-SYNC Installed in CSX200 Status 1 STS1 LED is REDWPIM-HDSL Installed in CSX200 WPIM-T1, WPIM-E1, or WPIM-DI Installed in CSX200 is in RED Alarm ModeStatus 1 STS1 LED is GREEN Status 1 STS1 LED is AMBERStatus 2 STS2 LED is OFF Status 2 STS 2 LED is RED WPIM-HDSL Installed in CSX200WPIM-HDSL is installed in CSX200 WPIM-T1, WPIM-E1, WPIM-DI, or WPIM-DDS Installed in CSX200Status 2 STS2 LED is GREEN Status 2 STS2 LED is AMBERTest TST LED is AMBER blinking Investigating Software Conﬁguration ProblemsConnection to Device Fails During Software Conﬁguration User Cannot Communicate with Remote Network StationCheck that TCP/IP Routing is set on and is enabled at the remote end Chapter 5 Troubleshooting CSX200 Installation Guide5-12 A WPIM Cable Speciﬁcations WPIM-T1CSX200 Installation Guide CSX200 Installation Guide Appendix A WPIM Cable SpecificationsTable A-3 provides RJ48 DTE pin assignments Table A-4 provides RJ48 network pin assignmentsWPIM-SY WPIM-SYAppendix A WPIM Cable Specifications EIA-449CSX200 Installation Guide Table A-7 provides pin assignments for the EIA-449 interface cableCSX200 Installation Guide V.35Table A-9 provides pin assignments for the V.35 interface cable WPIM-SYAppendix A WPIM Cable Specifications CSX200 Installation GuideTable A-9 V.35 Interface Cable Pin Assignment Continued CSX200 Installation Guide EIA-232Table A-11 provides pin assignments for the EIA-232 interface cable WPIM-SYAppendix A WPIM Cable Specifications X.21CSX200 Installation Guide Table A-13 provides pin assignments for the X.21 interface cableEIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 A ALT A CSX200 Installation Guide Appendix A WPIM Cable SpecificationsA-10 a ACWPIM-DDS WPIM-DDSWPIM-E1 Table A-20 provides WPIM-E1 DTE interface cable pin assignments CSX200 Installation GuideWPIM-E1 A-13WPIM-DI Table A-22 WPIM-DI Connector InformationTable A-23 WPIM-DI Network WPIM-HDSL WPIM-HDSLAppendix A WPIM Cable Specifications CSX200 Installation GuideA-16 B Speciﬁcations and Standards Compliance CSX200 Installation GuideTable B-1 Hardware Specifications CSX200 Regulatory Compliance Individual WPIM Regulatory ComplianceWPIM-T1 WPIM-SY WPIM-DDSIndividual WPIM Regulatory Compliance WPIM-E1 WPIM-DIWPIM-HDSL C FCC Part 68 - User’s Information for CSX200 Table C-1 WPIM-DI and WPIM-T1Table C-2 WPIM-DDS Only 6. If the telephone company alters their equipment in a manner that will affect use of this device, they must give you advance warning so as to give you the opportunity for uninterrupted service. You will be advised of your right to file a complaint with the FCC For the work to be performed in the certiﬁed territory of the control of a supervisor trained in accordance with D Glossary EtherTalk - AppleTalk protocols running on Ethernet Glossary RJ11 - Standard 4-wire connectors for telephone lines SNMP - Simple Network Management Protocol. A widely implemented Internet network management protocol that allows status monitoring, getting/setting of parameters for conﬁguration and control of network devices, such as routers and bridges Watchdog Frames - Frames sent out by servers to clients, under IPX, to verify that clients are still logged on Numerics IndexCSX200 Installation Guide IndexIndex-2