Cabletron Systems TM 9C300-1 MMAC

3-5

Monitoring Functions

LANVIEW LEDs

The LANVIEW LEDs on the front of the 9C300-1 Environmental Module may be

used as an aid in troubleshooting.

There are two LEDs visible to the user (Figure 3-4): the STATUS LED and the

ALARM LED.

Figure 3-4. 9C300-1 Environmental Module LANVIEW LEDs

The STATUS LED indicates the current status of the Environmental Module

processor and peripherals. The possible states and descriptions of the STATUS

LED are listed in Table 3-4.

Table 3-4. STATUS LED

LED Color State Description

Green Functional Fully operational.

Yellow/Green Booting Flashes green and yellow while booting.

Yellow Testing Testing system.

Yellow (Flashing) Crippled Not fully operational.

Red Reset Normal power-up reset.

Red (Flashing) Failed Fatal error has occurred.

Off Power off Lack of 5 volt input to the Environmental

Module.

1 2 3

9C300-1

STATU S

ALARM COM 1COM 2

EPIM

ENTER

4 5 6 7 8 9 10 11 12 13 14

MMAC

ALARM LED

STATUS LED

Contents

Main Page i Notice Notice ii Notice FCC Notice DOC Notice iii Contents Chapter 3 9C300-1 Environmental Module Operation Chapter 2 Installing the 9C300-1 Environmental Module Chapter 1 Introduction Chapter 4 Specications Appendix B Uninterruptible Power Supply (UPS) Appendix A EPIM Specications Introduction The 9C300-1 Environmental Module Using This Manual MMAC Features 1-3 Related Manuals Introduction 1-4 Getting Help 2-1 Chapter 2 Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental Module 2-2 3-1 Chapter 3 MMAC 9C300-1 Environmental Module Operation Monitoring Functions MMAC 3-2 External Ambient Temperature Monitoring Functions Fan Speed 3-4 System Humidity Internal Operating Temperature System Voltages MMAC 3-6 Out-of-Band Management Out-of-Band Management 3-7 COM1 and COM2 Ports 3-8 The Ethernet Port Interface Module (EPIM) LCD and Keypad ENTER CABLETRON SYSTEMS, INC. MMAC-PLUS <ALARMS> <SYSTEM> <MODULES> <SCREEN CONTRAST> Non-Interactive Mode Non-Interactive Mode Screens Page Page 3-12 Interactive Mode Interactive Mode Screens Main Screen Page 3-14 CHASSIS MAC ADDRESS xx-xx-xx-xx-xx-xx <PWR> <ENV> <COM> <DIAGS> <BBU> <EXIT> CHASSIS IP ADDRESS xxx.xxx.xxx.xxx CHASSIS HW REV xxx SN xxxxxxxxxxxx Page Page Page Page 3-19 Interactive Mode FW REV x.xx.xx SMB 1 FW REV x.xx.xx <ENV> <MEMORY> <BACKPLANE> <EXIT> MODULE xx STATUS ON-LINE HW REV xxx BOOT PROM REV x.xx.xx SN xxxxxxxxxxxx Page Page Page Page Page 4-1 Chapter 4 Specications Safety ! Specications 4-2 Physical Environmental Appendix A EPIM Specications Introduction EPIM-T A-2 EPIM-F1 and EPIM-F2 A-3 EPIM-F1 and EPIM-F2 A-4 EPIM-F3 A-5 EPIM-F3 A-6 EPIM-C Connector Type Grounding A-7 EPIM-A and EPIM-X (AUI Port) EPIM-A and EPIM-X (AUI Port) Page B-1 Appendix B Uninterruptible Power Supply (UPS) Introduction Connecting a UPS to an EM Uninterruptible Power Supply (UPS) B-2 Conguring COM Port for UPS