Cabletron Systems TM 9C300-1 Conguring COM Port for UPS

Uninterruptible Power Supply (UPS)

B-2

Figure B-1. Connecting EM to UPS

Conﬁguring COM Port for UPS

After the UPS has been connected to the COM2 port, the COM2 port must be

conﬁgured for UPS Management. To conﬁgure the COM2 port for UPS

Management, follow the steps below.

1. Connect the terminal or PC used for local management to the COM1 port on

the Environmental Module (EM) and press RETURN until the Slot Selection

Screen displays.

2. At the Slot Selection Screen, enter 0 (zero) to display the EM Conﬁguration

Screen.

3. At the EM Conﬁguration Screen, cursor to the Application Field for the

COM2 port.

4. Using the space bar, toggle to the UPS option.

5. Using the tab key, tab to the SAVE option and press RETURN.

If you need additional information about conﬁguring the COM ports, refer to the

Local Management User’s Guide.

9C3001

STATUS

ALARM COM 1 COM 2

EPIM

ENTER

MMAC

1 2 3 4 5 6 7 8 9 10 11 12 13 14

9 Pin D Connector Receptacle

COM Ports

MMAC-Plus Chassis (Front View)

Matrix UPS (Back View)

Contents

Main Page i Notice Notice ii Notice FCC Notice DOC Notice iii Contents Chapter 3 9C300-1 Environmental Module Operation Chapter 2 Installing the 9C300-1 Environmental Module Chapter 1 Introduction Chapter 4 Specications Appendix B Uninterruptible Power Supply (UPS) Appendix A EPIM Specications Introduction The 9C300-1 Environmental Module Using This Manual MMAC Features 1-3 Related Manuals Introduction 1-4 Getting Help 2-1 Chapter 2 Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental Module 2-2 3-1 Chapter 3 MMAC 9C300-1 Environmental Module Operation Monitoring Functions MMAC 3-2 External Ambient Temperature Monitoring Functions Fan Speed 3-4 System Humidity Internal Operating Temperature System Voltages MMAC 3-6 Out-of-Band Management Out-of-Band Management 3-7 COM1 and COM2 Ports 3-8 The Ethernet Port Interface Module (EPIM) LCD and Keypad ENTER CABLETRON SYSTEMS, INC. MMAC-PLUS <ALARMS> <SYSTEM> <MODULES> <SCREEN CONTRAST> Non-Interactive Mode Non-Interactive Mode Screens Page Page 3-12 Interactive Mode Interactive Mode Screens Main Screen Page 3-14 CHASSIS MAC ADDRESS xx-xx-xx-xx-xx-xx <PWR> <ENV> <COM> <DIAGS> <BBU> <EXIT> CHASSIS IP ADDRESS xxx.xxx.xxx.xxx CHASSIS HW REV xxx SN xxxxxxxxxxxx Page Page Page Page 3-19 Interactive Mode FW REV x.xx.xx SMB 1 FW REV x.xx.xx <ENV> <MEMORY> <BACKPLANE> <EXIT> MODULE xx STATUS ON-LINE HW REV xxx BOOT PROM REV x.xx.xx SN xxxxxxxxxxxx Page Page Page Page Page 4-1 Chapter 4 Specications Safety ! Specications 4-2 Physical Environmental Appendix A EPIM Specications Introduction EPIM-T A-2 EPIM-F1 and EPIM-F2 A-3 EPIM-F1 and EPIM-F2 A-4 EPIM-F3 A-5 EPIM-F3 A-6 EPIM-C Connector Type Grounding A-7 EPIM-A and EPIM-X (AUI Port) EPIM-A and EPIM-X (AUI Port) Page B-1 Appendix B Uninterruptible Power Supply (UPS) Introduction Connecting a UPS to an EM Uninterruptible Power Supply (UPS) B-2 Conguring COM Port for UPS