Cabletron Systems TM 9C300-1 - page 27

3-15

Interactive Mode

The Power Screen

Select <PWR> from the System Screen, as shown in Figure 3-15, to access

information about the chassis power supply conﬁguration.

Line 1 of the Power Screen, as shown in Figure 3-16, displays the number of

power supplies currently conﬁgured and the availability of power redundancy.

Lines 2 and 3 display the power supply status as either ON, OFF DUE TO

MANAGEMENT, or FAULT.

Line 4 is used to access information about a speciﬁc power supply module by

selecting a power supply number.

Figure 3-16. The Power Screen

Select <EXIT> to return to the System Screen.

The Power Supply Speciﬁc Screen

Select a power supply number from line 4 of the Power Screen, as shown in

Figure 3-16, to learn about a speciﬁc power supply in the MMAC-Plus chassis.

There is an LCD screen available for each installed power supply, as shown in

Figure 3-17.

Line 1 identiﬁes the power supply selected and its serial number.

Line 2 identiﬁes the power supply’s hardware revision, ﬁrmware revision of the

diagnostic controller and power loading factor as a percentage of its capacity.

Line 3 provides the input and output voltages of the power supply.

Figure 3-17. The Power Supply Speciﬁc Screen

Select <EXIT> to return to the Power Screen.

STATUS 1 ON 2 ON

<1>

SUPPLIES INSTALLED 2 PWR REDUNDANCY

<EXIT><2>

HW REV xxx FW REV x.xx.xx LOAD xxx%

<EXIT>

PWR SUPPLY 1 SN xxxxxxxxxxxx

PWR IN 110V PWR OUT 57.1V 5.1V 3.3V

Contents

Main Page i Notice Notice ii Notice FCC Notice DOC Notice iii Contents Chapter 3 9C300-1 Environmental Module Operation Chapter 2 Installing the 9C300-1 Environmental Module Chapter 1 Introduction Chapter 4 Specications Appendix B Uninterruptible Power Supply (UPS) Appendix A EPIM Specications Introduction The 9C300-1 Environmental Module Using This Manual MMAC Features 1-3 Related Manuals Introduction 1-4 Getting Help 2-1 Chapter 2 Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental Module Installing the 9C300-1 Environmental Module 2-2 3-1 Chapter 3 MMAC 9C300-1 Environmental Module Operation Monitoring Functions MMAC 3-2 External Ambient Temperature Monitoring Functions Fan Speed 3-4 System Humidity Internal Operating Temperature System Voltages MMAC 3-6 Out-of-Band Management Out-of-Band Management 3-7 COM1 and COM2 Ports 3-8 The Ethernet Port Interface Module (EPIM) LCD and Keypad ENTER CABLETRON SYSTEMS, INC. MMAC-PLUS <ALARMS> <SYSTEM> <MODULES> <SCREEN CONTRAST> Non-Interactive Mode Non-Interactive Mode Screens Page Page 3-12 Interactive Mode Interactive Mode Screens Main Screen Page 3-14 CHASSIS MAC ADDRESS xx-xx-xx-xx-xx-xx <PWR> <ENV> <COM> <DIAGS> <BBU> <EXIT> CHASSIS IP ADDRESS xxx.xxx.xxx.xxx CHASSIS HW REV xxx SN xxxxxxxxxxxx Page Page Page Page 3-19 Interactive Mode FW REV x.xx.xx SMB 1 FW REV x.xx.xx <ENV> <MEMORY> <BACKPLANE> <EXIT> MODULE xx STATUS ON-LINE HW REV xxx BOOT PROM REV x.xx.xx SN xxxxxxxxxxxx Page Page Page Page Page 4-1 Chapter 4 Specications Safety ! Specications 4-2 Physical Environmental Appendix A EPIM Specications Introduction EPIM-T A-2 EPIM-F1 and EPIM-F2 A-3 EPIM-F1 and EPIM-F2 A-4 EPIM-F3 A-5 EPIM-F3 A-6 EPIM-C Connector Type Grounding A-7 EPIM-A and EPIM-X (AUI Port) EPIM-A and EPIM-X (AUI Port) Page B-1 Appendix B Uninterruptible Power Supply (UPS) Introduction Connecting a UPS to an EM Uninterruptible Power Supply (UPS) B-2 Conguring COM Port for UPS