Cambridge Audio SR10 user manual Rear panel connections

Rear panel connections

SR10

4

Manufactured in an	FM 75Ω	AM 300Ω	Service Port	Important
ISO9001 approved facility				Please ensure that loudspeaker terminals are fully tightened.
				Veuillez s'assurer que les bornes de l'enceinte sont
				entièrement serrées

						Loudspeaker Terminals
						Impedance 4–8 ohms
Europe FM: 87.50MHz - 108.00MHz			Ground	5	Right	Left
US FM: 87.50MHz - 108.00MHz
Europe AM: 522kHz - 1629kHz
US AM: 530kHz - 1710kHz
					A	A
CD	DVD / BD	Aux / MP3	Phono MM	Out Rec
Left				Left		6
					B	B
Right				Right
CD	BD / DVD	MP3 / Aux	MM Phono	Rec Out	Right	Left
	1		2	3

Do not obstruct ventilation / Ventilation nicht verschließen / Ne pas obstruer la ventilation

Designed and engineered in London, England

Topaz SR10 Stereo Receiver

Rated Power Consumption: 500W

www.cambridge-audio.com

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

3132407

CONFORMS TO ANSI/UL

STD 60065

7TH EDITION 2003

CERTIFIED TO CAN/CSA

STD C22.2

No. 60065-03

Caution

Serial Number Label Removed

Mains Voltage Selector Switch

115V/230V AC~50/60Hz

7

Power AC

8Made under licence in China

ENGLISH

1 Audio inputs Aerials

These inputs are suitable for any ‘line level’ source equipment such as the audio outputs of CD players, BD/DVD players, etc.

2Phono input

This input has a built in phono stage. Record players fitted with Phono Cartridges of the Moving Magnet (MM) or high output Moving Coil (MC) type (between 2-6mV output and 30-50k load impedance) can be used. Low output Moving Coil types (<1mV and usually 10-1000 ohm load impedance) cannot be directly connected and will require a matching transformer or head amp. Please consult your dealer for details. The ‘ground’ terminals on both the record player and the SR10 should be connected (where possible) with a ground wire for lowest noise/hum pickup.

3Rec Out

Connect to the recording input of a tape deck, CD recorder input, etc.

4AM/FM antenna

Tuner aerial connections for picking up radio signals. Refer to the ‘Connections’ section of this manual. For permanent use, outdoor AM/FM aerials are highly recommended.

5Service port

For servicing use only. Do not connect anything here as it may result in damage.

6Loudspeaker terminals

Two sets of loudspeaker terminals are available, A (main loudspeaker terminals, top row) and B (secondary switchable loudspeaker terminals, bottom row). Connect the wires from your left channel loudspeaker to the Left positive and negative terminals, and the wires from the right channel loudspeaker to the Right positive and negative terminals. In each case, the red terminal is the positive output and the black terminal is the negative output.

Care should be taken to ensure no stray strands of wire are shorting speaker outputs together. Please ensure that the loudspeaker terminals have been tightened adequately to provide a good electrical connection. It is possible for the sound quality to be affected if the screw terminals are loose.

The use of A and B speakers affords you an easy and inexpensive way to create a simple multi-room system.

Note: When using two pairs of speakers, use speakers with a nominal impedance of 8 ohms.

7Voltage select switch

For servicing use only.

8AC power socket

Once all connections are complete, plug the AC power cable into an appropriate mains socket and turn the unit on.

	FM 75Ω	AM 300Ω		Service Port
						Designed and engineered in London, England
						Topaz SR10 Stereo Receiver
				Loudspeaker Terminals		Rated Power Consumption: 500W
				Impedance 4–8 ohms		www.cambridge-audio.com
			Ground
				A	A
CD	DVD BD/	xu/A MP3	Phono MM	OutRec
Lef				Left
				B	B
Right				Right
CD	BD / DVD	MP3 / Aux	MM Phono	Right	Left
				Rec Out

Note: The SR10 is supplied with a temporary aerial for initial use. For permanent use, outdoor aerials are highly recommended.

AM loop aerial

Connect each end of the single length antenna to the antenna terminals. Place the antenna as far from the main system as possible to prevent unwanted noise and to obtain optimum reception. If the AM loop aerial provided does not provide sufficient reception, it may be necessary to use an outdoor AM aerial.

FM aerial

Connect the supplied aerial to the FM 75 ohm socket. Extend and move the aerial lead around until you get the best reception. For continued use, we strongly recommend using a 75 ohm outdoor FM aerial.

5