Cambridge Audio SR10 user manual Technical specifications, Troubleshooting

Tuner settings

It is possible to change the tuner region settings for this unit. This can be necessary if the unit has been moved to a different country.

Two settings are possible which set the correct de-emphasis and tuning steps for either North America or Europe/Rest of the world.

Note: Changing the tuner settings will clear all stored presets. When moving the unit to another region the Voltage Select switch must be set to the correct mains supply voltage by an authorized dealer.

Menu

1 / 6 2 / 7 3 / 8 4 / 9 5 / 10

Press and hold both the 4/9 and Menu buttons at the same time. The display will show the software revision and followed by either a letter ‘A’ which represents North America or a letter ‘E’ which represents Europe/Rest of the world. Restart the unit by powering off and on.

Technical specifications

Power output	85 watts (into 8Ω)
THD (unweighted)	<0.01% @ 1kHz, 80% of rated power
	<0.15% 20Hz - 20kHz, 80% of rated power
Frequency response (-1dB)	5Hz - 50kHz
S/N ratio (ref 1W)	>82dB (unweighted)
Input impedances	47k ohms
Power Amp damping factor	>50
Max. power consumption	500W
Bass/Treble controls	Shelving, ultimate boost/cut
	+/- 10dB @ 100Hz and 20kHz
Dimensions	110 x 430 x 340mm
	(4.3 x 16.9 x 13.4”)
Weight	8.1kg (17.8lbs)

Tuners

Bands	European
	AM (522-1629kHz)
	FM (87.5-108MHz)
	US
	AM (530-1710kHz)
	FM (87.5-108MHz)
Aerial inputs	FM 75 ohms, Coaxial.
	AM 300 ohms wire loop/single wire.
Signal to noise	60dB typical (FM)
Distortion	<0.4% @ 1kHz 50kHz deviation (FM mono)
	<0.6% @ 1kHz 50kHz deviation (FM stereo)

SR10

Troubleshooting

There is no power

Ensure the AC power cord is connected securely.

Ensure the plug is fully inserted into the wall socket and is switched on. Check fuse in the mains plug or adaptor.

Check the power is on at the front of the unit.

There is no sound

Check the correct input is selected.

Check that the speakers are connected correctly.

If using the tuner, check aerial connections and an available station is selected.

Check the unit is not in mute mode.

Check the Speaker A/B configuration matches your speakers.

The sound is distorted

Check aerial connections and placements.

Check speaker connections.

There is a hum coming from the speaker

Ensure that all cable connections are secure, particularly ground/shield connections. For turntables.

There is unwanted background noise and interference

Move the unit away from other electrical equipment that is likely to cause interference.

Re-orientate the aerial.

Ensure that all cable connections are secure, particularly ground/shield connections for turntables.

The remote handset will not function

Check that the batteries have not expired.

Ensure that nothing is blocking the remote sensor.

Over temperature protection

The unit has an over temperature and shutdown protection. If the unit is continuously used for a long period and over heats, the unit will shut down. Leave the unit ‘ON’ for 10 minutes to cool down, then turn the unit off and on to continue listening.

If the problem persists, then the unit is being over driven. Reduce the volume level, and ensure the unit is in an open ventilated area to resolve the problem.

Use of two pairs of speakers which are less than 8 Ohms can cause overloading and is not recommended.

In the event that the above solutions do not remedy your problem, please consult our frequently asked questions (FAQ) section on our website: www.cambridge-audio.com/sts/faqs

For all servicing, in or out of warranty, please contact your dealer.

ENGLISH

11