Manual de Instrucciones y Lista de Piezas
DG460300CK
Garantía Limitada
1DURACION: A partir de la fecha de compra por el comprador original tal como se especifica a continuación: Un año
2. | QUIEN OTORGA ESTA GARANTIA (EL GARANTE: Campbell Hausfeld / The Scott Fetzer Company | |
| 100 Production Drive, Harrison, Ohio 45030 Teléfono: (800) | |
3. | QUIEN RECIBE ESTA GARANTIA (EL COMPRADOR): El comprador original (que no sea un revendedor) del | |
| producto Campbell Hausfeld. | |
4. | PRODUCTOS CUBIERTOS POR ESTA GARANTIA: Cualquier herramienta a motor de Campbell Hausfeld | |
| proporcionada o fabricada por el garante. | |
5. | COBERTURA DE LA GARANTIA: Los defectos substanciales de material y fabricación que ocurran dentro | |
| del período de validez de la garantía. | |
6. | LO QUE NO ESTA CUBIERTO POR ESTA GARANTIA: | |
| A. | Las garantías implícitas, incluyendo aquellas de comercialidad E IDONEIDAD PARA FINES |
|
| PARTICULARES, ESTAN LIMITADOS A LO ESPECIFICADO EN EL PARRAFO DE DURACION. Si este producto |
|
| es empleado para uso comercial, industrial o para alquiler, no se aplicará ninguna garantía. En algunos |
|
| estados no se permiten limitaciones a la duración de las garantías implícitas, por lo tanto, en tales casos |
|
| esta limitación no es aplicable. |
| B. CUALQUIER PERDIDA DAÑO INCIDENTAL, INDIRECTO O CONSECUENTE QUE PUEDA RESULTAR DE UN | |
|
| DEFECTO, FALLA O MALFUNCIONAMIENTO DEL PRODUCTO CAMPBELL HAUSFELD. En algunos estados |
|
| no se permite la exclusión o limitación de daños incidentales o consecuentes, por lo tanto, en tales |
|
| casos esta limitación o exclusión no es aplicable |
| C. | Cualquier falla que resulte de un accidente, abuso, negligencia o incumplimiento de las instrucciones de |
|
| funcionamiento y uso indicadas en el (los) manual(es) que se adjunta(n) al producto. Dichos accidentes, |
|
| abusos por parte del comprador, o falta de operar el producto siguiendo las instrucciones del manual |
|
| de instrucciones suministrado también debe incluir la desconexión o modificación de los instrumentos |
|
| de seguridad. Si dichos instrumentos de seguridad son desconectados, la garantía quedaría cancelada. |
| D. | Los ajustes normales explicados en el(los) manual(es) suministrado(s) con el producto. |
7. | RESPONSABILIDADES DEL GARANTE BAJO ESTA GARANTIA: Reparar o reemplazar, como lo decida el | |
| Garante, los productos o componentes que estén defectuosos, se hayan dañado o hayan dejado de | |
| funcionar adecuadamente, durante el período de validez de la garantía |
General Safety Information (Cont’d.)
6.Store tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
7.Avoid cutting nails. Inspect workpiece for any nails and remove them before operation.
8.Do not cut hollow pipe.
9.Do not cut oversize workpiece.
10.Check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor, workbench, etc.
11.Make sure the blade is not contacting the workpiece before the switch is turned on.
12.Keep hands away from moving parts.
13.Do not leave the tool running. Operate the tool only when hand- held.
14.Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece.
15.Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin.
Assembly
ATTACHING THE BLADE
Saw Blade |
Holder Bolts |
Saw Blade - |
Blade Teeth |
Facing |
Forward |
Figure 1 |
4.Loosen the base adjustment bolts. Slide the blade support bearing forward so that the blade is riding in the groove. Retighten the base adjustment bolts. Check this adjustment when ever the blade is changed or the base is adjusted.
To remove the blade, follow the installation procedure in reverse.
NOTICE | Occasionally |
lubricate the roller. |
Pre-Operation
Proper planning can prevent accidents when using power tools. Plan your cuts ahead of actually doing them. Mark a cutting line on the work piece to ensure you know the direction you need to take while using the tool.
Operation
!WARNING glassesSafety and ear protection must be worn during operation.
Make sure work
! CAUTION is held securely in vise or clamped in place prior to starting operation. Loose work may spin and cause bodily injury.
Keep hands away ! DANGER from cutting area
and blade.
Always hold the base flush with the workpiece. Failure to do so may cause blade breakage, resulting in a serious injury. Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may cause a slanted cutting surface and blade breakage.
Turn the tool on without the blade making any contact and wait until the blade attains full speed. Then rest the base flat on the workpiece and gently move the tool forward along the previously marked cutting line.
8. RESPONSABILIDADES DEL COMPRADOR BAJO ESTA GARANTIA: |
A. Suministrar prueba fechada de compra y la historia de mantenimiento del producto. |
B. Entregar o enviar el producto o componente Campbell Hausfeld al Centro de Servicio autorizado |
Campbell Hausfeld más cercano. Los gastos de flete, de haberlos, deben ser pagados por el comprador. |
C. Seguir las instrucciones sobre operación y mantenimiento del producto, tal como se indica(n) en el (los) |
manual(es) del propietario |
Esta garantía limitada es válida sólo en los EE.UU., Canadá y México y otorga derechos legales específicos. Usted también puede tener otros derechos que varían de un Estado a otro. o de un país a otro.
Always unplug tool and place the switch in the off position before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.
Always clean out
! CAUTION all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause insufficient tightening of the blade, resulting in a serious personal injury.
1. Loosen the two bolts counterclockwise on the blade holder with the allen wrench (see Figure 1).
2. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the blade support bearing (see Figure 1) .
3. Tighten the bolt clockwise to secure the blade.
1. | On/Off Switch | 2 |
2. | Lock Button | 1 |
3.Safety Guard / Dust Guard
4. Saw Blade Holder Bolts
5. Base
6.Dust Extraction Port
7.Dust Extraction Attachment
8.Blade Support Bearing
7
3 |
| 6 | |
|
| ||
4 |
| Base Angle | |
5 |
| ||
8 | Degree Guide | ||
|
Figure 2
22 Sp
www.chpower.com
3