Campbell Hausfeld Compresor lubricado con aceite HL5402 Troubleshooting Chart, 26 Sp

Compresor lubricado con aceite

HL5402

Troubleshooting Chart (Continued)

		5
		4
			3	2
	6
	7
	8		10
	9
	10		11
16	15		12
17		8	13
	18
18			25
19	21		14	24a
20	22
23	33	25
	32	26
27				39
	28			38
	29			36
30			2625	37
31
			34
		4
			35
		21

55

56

57

59

58

		1
				46
		44	44f
				49
				48
				47
				45
			44d44e
			44c
24			44a 44b
			43
	41	42
40		50
				72
		51
		71
		70
54			69
			68	52
				67
		52
	55	53
56			66
		65

		63
60	61	64

61

62

Symptom	Possible Cause(s)			Corrective Action
Tank pressure drops	1.	Loose drain valve	3. Replace or repair as necessary.
when compressor shuts	2.	Check valve leaking	1.		Tighten.
off	3.	Loose connections at fittings, tubing,	2.		Remove check valve. Clean or replace.
		etc.	3.		Check all connections with soap and water solution.
					If a leak is detected, (1) tighten or (2) remove fitting
					and apply pipe tape to threads and reassemble.
	4.	Tank leaks	4.		Check tank for leaks with soap and water solution. If
					leak is detected, tank must be replaced with genuine
					replacement part.
						Do not disassemble check
						valve with air in tank;
			bleed tank
Compressor runs	1.	Excessive air usage, compressor too	1.		Decrease usage or purchase unit with higher air
continuously and air		small			delivery (SCFM).
output is lower than	2.	Clogged intake filter	2.		Clean or replace.
normal/low discharge	3.	Loose connections at fittings, tubing,	3.		Check all connections with soap and water solution.
pressure		etc.			If a leak is detected, (1) tighten or (2) remove fitting
					and apply pipe tape to threads and reassemble.
	4.	Tank leaks	4.		Check tank for leaks with soap and water solution. If
					leak is detected, tank must be replaced with genuine
	5.	Broken valves			replacement part.
	6.	Piston ring worn	5.		Replace compressor valves as necessary.
			6.		Replace piston rings.
Excessive moisture in	1.	Excessive water in tank	1.		Drain tank.
discharge air	2.	High humidity	2.		Move to area of less humidity; use air line filter.
					NOTE: Water condensation is not caused by
					compressor malfunction.
Compressor runs	1.	Defective pressure switch	1.		Replace switch.
continuously and safety	2.	Defective safety valve	2.		Replace safety valve with genuine replacement part.
valve opens as pressure
rises
Excessive starting and	1.	Excessive condensation in tank	1.		Drain more often.
stopping (auto start)	2.	Loose connections at fittings, tubing,	2.		Check all connections with soap and water solution.
		etc.			If a leak is detected, (1) tighten or (2) remove fitting
					and apply pipe tape to threads and reassemble.
	3.	Tank leaks	3.		Check tank for leaks with soap and water solution. If
					leak is detected, tank must be replaced with genuine
					replacement part.
						Do not disassemble check
						valve with air in tank;
			bleed tank
Air leaking from	1.	Check valve stuck in an open position	1.		Repair or replace check valve.
unloader valve on	2.	Unloader valve stuck in open position	2.		Repair or replace unloader valve.
pressure switch						Do not disassemble check
						valve with air in tank;
			bleed tank

26 Sp 7