Operating Instructions and Parts Manual | Models WF2050, WF2054 & WF2057 |
Manual de Instruccones y Lista de Repuestos | Modèles WF2050, WF2054 et WF2057 |
Instructions D’Utilisation et Manuel de Pièces | Modelos WF2050, WF2054 y WF2057 |
Service Record État de Service Registro de servicio
Wire Feed Arc Welder
Soudeur À L’Arc Alimenté En Fil
Soldadora Con Arco Con Alambre Continuo
Operating Instructions & Parts Manual | Models WF2050, WF2054 & WF2057 |
|
|
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
Wire Feed | UA |
|
|
|
|
| Need |
| M |
|
|
|
|
|
|
| URAN |
|
|
|
|
|
|
|
| SS CE |
| ||
|
|
|
|
| A |
| P |
| |
|
|
|
|
|
| R |
| ||
|
|
|
| Y |
|
| O | ||
|
|
| T |
|
|
| G | ||
|
| L | I |
|
|
|
| R | |
| Q |
| Assistance? | A | |||||
Arc Welder |
|
|
| ||||||
| Call Us First! |
BUILT TO LAST
Date |
| Maintenance performed |
| Replacement components required |
Date |
| Entretien complété |
| Pièces de rechange exigées |
Fecha |
| Mantenimiento realizado |
| Repuestos requeridos |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Description
This Campbell Hausfeld welder is a 70 amp, single phase 115 volt input, wire feed arc welding machine. This unit is equipped with infinite wire speed control to accurately select the proper wire feed rate needed for various welding conditions. Internal components are thermostatically protected.
This welding system is designed for use with the Flux Cored Arc Welding (FCAW) process. As delivered from the factory, this welder can weld with .030” (.8 mm) or .035” (.9 mm) diameter
Unpacking
All welding accessories for the welder are inside the wire feed compartment on side of welder.
5 4
7
3
8
6
1
2
Figure 1 - Welder Components and Controls
When unpacking, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings and screws, etc. are tightened before putting unit into service. Report any missing or damaged items by calling
Circuit Requirements
This equipment
!CAUTION requires a dedicated
115 volt circuit. Refer to the following chart for the correct circuit breaker or fuse rating. Do not run other appliances, lights, or tools on this circuit while operating this equipment. Extension cords are not recommended. Blown fuses and tripped circuit breakers can result from failure to comply with this recommendation.
Heat | Circuit Breaker or |
Selector | Slow Blow Fuse |
Low | 15 amp |
High | 20 amp |
See page 5 for supply cable replacement instructions.
Components and Controls
1.Work Clamp - connects to work piece.
2.Wire Feed Gun with .035” tip.
3.Power Cord - plug into 115 volt outlet.
4.On/Off Switch.
5.Infinite Wire Speed Control - turn clockwise to increase wire speed and counterclockwise to decrease wire speed.
6.Heat Selector - Selects welding power. Two selections are possible; low and high.
7.Light - illuminates if thermostat has automatically shut off unit.
8.Wire Feed Compartment.
General Safety
Danger means a ! DANGER hazard that will
cause death or serious injury if the warning is ignored.
Warning means a ! WARNING hazard that could
cause death or serious injury if the warning is ignored.
Caution means a ! CAUTION hazard that may
cause minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property.
NOTE: Note means any additional information pertaining to the product or its proper usage.
!WARNING
Always keep a fire extinguisher accessible while performing arc welding operations.
www.chpower.com
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2006 Campbell Hausfeld/Scott Fetzer | For parts, manuals, product & service information | IN972800AV 1/06 |
visit www.chpower.com