Installing a CF Card | Canon PowerShot A10, PowerShot A20 specification

Battery Performance

	Number of Shots		Replay
	LCD Monitor ON	LCD Monitor OFF	Time
AA Alkaline
Batteries	Approx.	Approx.	Approx.
(included with	200 shots	500 shots	240 min.
the camera)
AA NiMH	Approx.	Approx.	Approx.
Battery NB-1AH	350 shots	1000 shots	240 min.

*The actual performance may vary from the above data according to the shooting conditions and the selected recording mode.

<Test Conditions>

Shooting: Room temperature (23 ° C, 73 ° F), alternating between wide angle and telephoto every 20 seconds, flash used one in four shots, power turned off and on again after every eighth shot.

Replay: Room temperature (23 ° C, 73 ° F), continuous replay at 3 seconds per image.

Battery Status Indications

The LCD monitor displays an icon or message to let you know when batteries are low or depleted.

Batteries are beginning to run low. Replace (or recharge) batteries promptly.

If the LCD monitor is off, this icon will appear when you press any of

		the following buttons: ,					/ , or
		/ .
	Change	Batteries are fully depleted and the
	Change	camera can no longer operate. You
	the	camera can no longer operate. You
	the	should replace the batteries
	batteries	should replace the batteries
	batteries	immediately.
		immediately.

Installing a CF Card

1 Be sure that the camera is turned off.

20

Image 22

Canon PowerShot A10, PowerShot A20 manual Installing a CF Card, Be sure that the camera is turned off

Contents

Camera User Guide Precautions Replaying Table of Contents Index Read This First Warranty LimitationsTest Shots Safety Precautions Page Page Page If Condensation Forms Inside the Camera Avoid Condensation Related ProblemsAvoid Strong Magnetic Fields Extended Storage Press the main switch to turn the camera on p Install the batteries pInstall the CF card p Turn the mode dial to Auto p Take the shot p Quick Erase Set the focus pView the recorded image LCD monitor displays the print menu Connect the camera to the printer pPress or button to select OK, and press the SET button Printer starts printing the selected image Guide to Components Preparing the CameraFront View Back View Operation Panel Mode Dial Indicators Lower Indicator Installing the BatteriesYellow Macro mode Proper Battery Handling Close the battery cover Never use batteries that look like this Installing a CF Card Be sure that the camera is turned off Arrow, and open it Slide the CF card slot coverDirection of the gray Insert the CF card into PowerShot A10 About CF Cards PowerShot A20 Attaching the Wrist Strap Setting the Date and Time 94, then reset the date and time as explained below Press the Menu button Rec. Menu will display Setting the Language Turn the mode dial to Press the Menu button Select the desired language If you wish to cancel, press the Menu button insteadPress the SET button Basic Functions Turning the Camera On Using the Viewfinder Camera includes an optical viewfinder Using the LCD Monitor About the Autofocus Function Single Image Replay ModesMode Standard Detailed No display Information Displayed on the LCD Monitor Shooting ModeFollowing information appears on the LCD monitor Replay Mode Detailed Display Replay Mode Standard DisplayDetailed mode, the following information is also shown Pressing the Shutter Button Pressing halfway Press the shutter button lightly Reviewing an Image Immediately after Recording It Keep the shutter button down Telephoto/Wide Angle Using the ZoomDigital Zoom Select a shooting mode Selecting a Shooting ModeChanging Resolution Compression Setting Shooting Press or button as necessary to adjust the setting Using the Flash You can set the flash mode to match the shooting conditions Take the shot Red-Eye Reduction Turn the mode dial to Press the / button to Select or Shooting Close-Ups/ Infinity Shots Using the Focus Lock How to Use the Focus Lock Using the Self-Timer Shooting Continuously To stop shooting, release the shutter button Adjusting the Exposure Compensation Press or button as necessary to adjust the compensation Setting the White Balance Press the SET button Take the shot Necessary to display PressWhite Balance menu Press the SET button Stitch Assist Mode Framing a Subject Shooting Take the first shot After taking the final image, press the SET button You can take as many as 26 images Functions Available in Each Shooting Mode Magnifying an Image ReplayingDisplaying Images Singly Single Image Replay Press the button Displaying Images in Sets of Nine Index Replay Turn the mode dial to Press the buttonLCD monitor displays an index of 9 images Use or button to select an image Switching between Sets of Nine ImagesPress or button to change the displayed images Rotating Images in the Display Automating Playback Auto Play Camera reads the images on the CF card and starts auto play Protecting Images Press the Menu button to close this featureTo cancel protection Protected images are identified by the Protected Icon Erasing Images Singly ErasingLCD monitor asks for confirmation Erasing All Images Press or button to select OK, and then press the SET button Press or button to select OK, and then press the SET button Print Settings Dpof Settings Displaying the Print Order Menu Setting the Print Style You can set up the print style as follows Print Type When you are finished making settings, press the Menu button Selecting Images for Printing Selection method will vary according to the print type Resetting the Print Settings When you are finished, press the Menu button Press or button to select OK, and press the SET button Connecting the Card Photo Printer CP-10 Printing with the Card Photo Printer CP-10 Camera power is turned on and set the mode dial to Printing Printing with Dpof Print Settings Printing stops or restarts accordingly Stop Printing LCD monitor displays a confirmation message Resuming Printing You can select the style settings for your prints Image Date Rec. Menu can not be shown in mode Camera SettingsDisplaying the Rec. Menu Changing the Image Review Time Resetting the File Number Display the Rec. Menu p About file numbering Setting the Beep On/Off You should format new CF cards before using them Formatting a CF Card Changing Other Settings Auto Power Down Video Signal Format Connecting the Camera to a TV Set Turn on the camera Downloading Directly from a CF Card Downloading Images to a ComputerInserting the CF Card CF Card Reader Downloading Images Image Folder Organization and File Names Connecting the Camera to a Computer with a USB Cable Supported Operating Systems Connection Precautions Connecting to a USB Port Turn the camera’s mode dial to Replacing the Date Battery Appendix Pull the battery out of the holder, as shown Using the Optional Battery Kits Using Rechargeable Batteries Battery and Charger Kit CBK100 Using the Household Power Source AC Adapter Kit ACK600 To an electrical outlet Using Optional Lenses and Lens Adapters Wide Converter WC-DC52 Close-Up Lens 250D 52 mm Conversion Lens Adapter LA-DC52 52 mm Attaching a Lens 101 Using the Soft Case Optional Camera Care and Maintenance When the camera becomes dirty, clean it as follows Troubleshooting Problem Cause Solution 105 106 Problem Cause Solution 108 List of Messages Busy 110 111 Specifications PowerShot A10 PowerShot A20 113 NiMH Battery NB-1AH optional CompactFlash Card Camera Settings Index 117 Canon Customer Support Canon Danmark A/S Canon Luxembourg S.ACanon Nederland N.V Canon España S.A Canon Marketing Services Canon Marketing Malaysia Sdn. Bhd FCC Notice Digital Camera, Model PC1007 and PC1009 CDI-E017-010