adding the MAC address to the end of the Network Number. The Network Number of a new UPC Open controller is 16101, but it can be changed using i-Vu®Tools or BACView device. By default, a MAC address of 20 will result in a Device In- stance of 16101 + 20 which would be a Device Instance of 1610120.

CONFIGURING THE BAS PORT FOR BACNET MS/ TP — Use the same baud rate and communication settings for all controllers on the network segment. The UPC Open con- troller is fixed at 8 data bits, No Parity, and 1 Stop bit for this protocol's communications.

If the UPC Open controller has been wired for power, pull the screw terminal connector from the controller's power termi- nals labeled Gnd and HOT. The controller reads the DIP Switches and jumpers each time power is applied to it.

Set the BAS Port DIP switch DS3 to “enable.” Set the BAS Port DIP switch DS4 to “E1-485.” Set the BMS Protocol DIP switches DS8 through DS5 to “MSTP.” See Table 9.

Table 9 — SW3 Protocol Switch Settings

for MS/TP

DS8

DS7

DS6

DS5

DS4

DS3

Off

Off

Off

Off

On

Off

Verify that the EIA-485 jumpers below the CCN Port are set to EIA-485 and 2W.

The example in Fig. 29 shows the BAS Port DIP Switches set for 76.8k (Carrier default) and MS/TP.

Set the BAS Port DIP Switches DS2 and DS1 for the appro- priate communications speed of the MS/TP network (9600, 19.2k, 38.4k, or 76.8k bps). See Fig. 29 and Table 10.

Table 10 — Baud Selection Table

BAUD RATE

DS2

DS1

9,600

Off

Off

19,200

On

Off

38,400

Off

On

76,800

On

On

Fig. 29 — DIP Switches

DIP switch 3 is used to set up which port the building net- work is connected to. This DIP switch will always be set to OFF.

DIP switch 4 is used to tell the UPC controller the commu- nication language of the building network. This should always be set to ON, unless the network uses BACnet over ARC156.

DIP switches 5-8 are used to set up the communication pro- tocol. See Table 11 for settings.

NETWORK POINTS AND DESCRIPTIONS — The points list for the controller is shown in Table 12.

BP (AV:1) — The BP (AV:1) parameter is a read-only value that shows the current building pressure from the building pres- sure sensor inside the ERV. This parameter is only applicable for a building pressure based mode of operation.

DCV CO2 INSIDE (AV:2) — This parameter shows the read- ing from the CO2 sensor that is connected to the ERV. The CO2 sensor is only provided with the ERV when the ERV has been ordered with a CO2 based EzERV control scheme.

EAT SENSOR (AV:3), OAT SENSOR (AV:7), RAT SEN- SOR (AV:9), AND SAT SENSOR (AV:19) — These status points show the temperatures in all 4 quadrants of the ERV. The status points will only display values other than 0 if the ERV was ordered with temperature sensors.

EXHAUST AIR CFM (AV:5) AND OUTSIDE AIR CFM (AV:8) — These status points provide the airflow that each fan is moving if the ERV was ordered with the EzERV option. This option is an integrated airflow monitoring station.

EX FAN POS (AV:4) AND OA FAN POS (AV:6) — The fan speed status points provide feedback on a scale of 0 to 100% to show the output of each fan.

REMOTE AIRFLOW CONFIGURATION MODE (AV:10)

This mode sets up the mode of operation for the ERV. The setting is associated with the control scheme the ERV was ordered with from the factory. The appropriate setting for this mode correlates with the last 3 characters of the part number on the ERV.

• For part number G-A, the mode is Offset Airflow Con- trol (mode no. 1).

• For part number G-B, the mode is CO2 sensor based Demand Control Ventilation with Offset Airflow Control (mode no. 2).

• For part number G-D, the mode is Building Pressure sen- sor based Airflow Control (mode no. 3).

• For part number G-E, the mode is CO2 sensor based Demand Controlled Ventilation with Building Pressure sensor based Airflow Control (mode no. 4).

• If the ERV part number does not have "G-" in it then mode no. 0 should always be used.

Table 11 — UPC Communication Protocol Settings (DIP Switches 5-8)

PROTOCOL

 

 

DIP SWITCH

 

TYPE

5

6

 

7

8

BACnet MSTP (m)

OFF

OFF

 

OFF

OFF

BACnet MSTP (s)

ON

OFF

 

OFF

OFF

BACnet PTP

OFF

ON

 

OFF

OFF

N2

ON

ON

 

OFF

OFF

Modbus

OFF

OFF

 

ON

OFF

LON SLTA

ON

OFF

 

ON

ON

LON Plugin

OFF

ON

 

ON

ON

Ethernet

ON

ON

 

ON

ON

30

Page 30
Image 30
Carrier 62E SW3 Protocol Switch Settings For MS/TP, Baud Selection Table, UPC Communication Protocol Settings DIP Switches

62E specifications

The Carrier 62E is a highly regarded air conditioning unit known for its efficiency, reliability, and advanced technology features. Designed to cater to both residential and light commercial applications, this model is recognized for its ability to provide optimal cooling performance even in challenging climates.

One of the standout features of the Carrier 62E is its energy efficiency. The unit boasts a high Seasonal Energy Efficiency Ratio (SEER) rating, which ensures significant energy savings over time. This efficiency not only translates to lower energy bills for users but also contributes positively to environmental sustainability. The Carrier 62E is designed with eco-friendly refrigerants that minimize its carbon footprint while maintaining high performance levels.

In terms of technology, the Carrier 62E comes equipped with innovative smart controls. The unit can be integrated with smart home systems, allowing users to control their cooling preferences through their smartphones or other connected devices. This feature enhances convenience, enabling homeowners to adjust temperatures and monitor their system remotely, ensuring maximum comfort regardless of their location.

The 62E is engineered with a durable and robust build, ensuring long-lasting reliability. The components are crafted to withstand harsh weather conditions, making it a solid investment for users in varied climates. Additionally, the unit operates quietly, thanks to its advanced sound-dampening technologies, ensuring that indoor environments remain peaceful and undisturbed.

Installation of the Carrier 62E is straightforward, thanks to its versatile design and flexibility. The system can be configured for various ductwork arrangements, adapting seamlessly to different home layouts and existing infrastructure.

Another notable characteristic of the Carrier 62E is its advanced filtration system. The unit comes with a high-efficiency filter that captures airborne particles, allergens, and pollutants, promoting cleaner and healthier indoor air quality. This is an essential feature for households with allergy sufferers, as it helps create a more comfortable living space.

Overall, the Carrier 62E stands out as a leader in residential and light commercial air conditioning solutions. With its energy efficiency, state-of-the-art technology, durable design, and air quality improvements, it meets the diverse needs of modern users while providing remarkable comfort throughout the year. As climate considerations become increasingly important, the Carrier 62E remains a compelling choice for those seeking to enhance their home's comfort while being mindful of energy consumption and environmental impact.