Manuals / Carrier Access / Computer Equipment / Computer Hardware

Carrier Access EdgeFLEX, 600 installation manual Installing the Decorative Bezel, Connecting Power

Models: 600 EdgeFLEX

1 54

Download 54 pages 436 b

Page 25

EdgeFLEX 600 Installation

Installing the Decorative Bezel

Installing the Decorative Bezel

A decorative bezel is included in the Accessory Kit to cover the fan tray and air filter. Snap the bezel onto the ball stud as shown in the following illustration.

Connecting Power

DANGER! BEFORE INSERTING OR EXTRACTING A EDGEFLEX 600 DC POWER SUPPLY UNIT, ENSURE THAT THE PSU’S CIRCUIT BREAKER SWITCH IS IN THE OFF POSITION, AND THAT THE DC

POWER CONNECTOR HAS BEEN UNPLUGGED.

Requirements for DC Power Connections

The EdgeFLEX 600 DC model can be powered from a DC supply operating between -40 and -72 VDC. The power connector is located on the front of the Power Supply Module(s), which are located in the top two slots of the EdgeFLEX 600 chassis. The PSU modules are redundant and hot-swappable.

Use a separate circuit breaker to power each power supply. This will allow one power supply to keep the EdgeFLEX 600 operating while the other power supply is powered down for maintenance.

Use 7 to 8 gauge wire for up to 50 foot run to power the device. Use a circuit breaker rated for 25 Amps for the power leads.

EdgeFLEX 600 - Release 2.0

2-7

Image 25

Carrier Access EdgeFLEX, 600 Installing the Decorative Bezel, Connecting Power, Requirements for DC Power Connections

Contents

EdgeFLEX Page Compliance Safety of Information Technology EquipmentFCC Requirements, Part Industry Canada ICES-003Europe EN55022 and AS/NZS CISPR22 Nebs Level 3 Requirements Compliance EdgeFLEX 600 Release Class 1 Laser Product Safety Warning Safety NoticesDC Power Supply Warnings AC Power Supply Service and Maintenance End UserDC Power Supply Safety Information Electrostatic Discharge ESD Precautions Limitation of Warranty & Limitation of Remedies WarrantyWarranty Product Returns Table of Contents Adding and Replacing Components Connector Pin AssignmentsIndex Chapter EdgeFLEX 600 Front View Hardware OverviewSite Planning Technical SpecificationsCompliance Specifications Environmental SpecificationsRelated Documentation EdgeFLEX 600 Installation Required Tools to Unpack and Install the Chassis Preparing for InstallationChecking the Contents Unpacking the EdgeFLEXPower Supply Unit LED Locations Fan Tray, System Interfaces, and Power Supply UnitsChassis Components Front Panel LEDs and System Interfaces LocationsInstalling Flanges on the Chassis Installing the EdgeFLEX 600 Chassis in a RackEdgeFLEX 600 Installation Rack Installation Connecting Power Installing the Decorative BezelRequirements for DC Power Connections Connecting Chassis to Ground Wiring and Connecting DC Power System Management Connectors Connecting System CablesConnecting the Management Cables System Management ConnectionsConnecting the Timing Input Cable Connecting the Local Console CableConnecting the Timing Output Cable Connecting the Alarm ContactsSelecting the Appropriate Network Cables Connecting Network CablesConnecting to DS1/E1 Interfaces Connecting to 10/100 Ethernet InterfacesConnecting to Optical Interfaces Powering Up the Chassis Powering Up and Checking LEDsCard LED Locations Check Management Port Ethernet LEDs Checking System Status LEDsCheck I/O Card LEDs Card Type LED Label Description Normal State Alarm StateRouting System and Network Cables Routing CablesAdding and Replacing Components Replacing the Air Filter Replacing a Fan Tray Adding and Replacing Components Replacing an SFP Module Removing/Installing Cards Card Removal/Insertion Operating the Ejector LatchesAdding and Replacing Components Nonreplaceable Components Nonreplaceable Components EdgeFLEX 600 Release Appendix a Ethernet RJ-45 Pinout management port Pin LocationsTiming Port Pinout Serial Port PinoutTiming In Ports Timing Out Ports Alarm Inputs PinoutAlarm Outputs Pinout Alarm Outputs Pinout EdgeFLEX 600 Release Index Index