Operation of Your Opener

Activate the opener with any of the following:

•The Remote Control Transmitter.Hold push button down until the door starts to move.

•The Door Control.Hold push bar or button down until the door starts to move.

•The Outside Keylock or Keyless Entry.

(See Accessories)

When the opener is activated with the safety reversing sensor installed and correctly aligned:

1. If open, the door will close. If closed, it will open.

WARNING

Weak or broken springs could allow an open door to fall (either rapidly or unexpectedly), resulting in serious injury, death or property damage. If possible, use the manual release rope and handle only when the door is fully closed.

2.If closing, the door will reverse.

3.If opening, the door will stop (allowing space for entry and exit of pets and for fresh air).

4.If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse.

6.If obstructed while opening, the door will stop.

7.The garage door will reverse in the closing cycle, and the opener lights will blink for 5 seconds, when the invisible beam is broken. If fully open, the door will not close when the beam is broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is not aligned correctly, the door won't close from any remote transmitter. You can close the door with the Door Control, the Outside Keylock, or Keyless Entry, however, if you activate them until down travel is complete. If

Trolley

Trolley

ReleaseArm

(in Manual

Disconnect

Position)

NOTICE

Lockout position(Manual disconnect)

To open the door manually: The door should be fully closed if possible. Pull down on the manual release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually. The lockout feature prevents the trolley from reconnecting auto- matically, and the door can be raised and lowered manually as often as necessary.

you release them too soon, the door will reverse.

Opener Lights will turn on under the following conditions: When the opener is initially plugged in; when the power is interrupted; when the opener is activated. It will turn off automatically after 4-1/2 minutes or provide constant light when the Light feature on the Multi-Function Door Control is activated. Bulb size is 100 watts maximum.

Lights will also turn on when someone walks through the open garage door. With a Multi-Function Door Control, this feature may be turned off as follows: With the opener lights off, press and hold the light button for 10 seconds, until the light goes on and off again. To restore this feature, start with the opener lights on, then press and hold the light button for 10 seconds.

To reengage the trolley: Pull the manual release handle toward the opener at a 45 degree angle so that the trolley release arm is horizontal. The trolley will reconnect on the next UP or DOWN operation, either manually or by pressing the Door Control push bar or button.

Trolley

Trolley

Release Arm

Manual

 

Release

NOTICE

Handle

 

(Pull at 45° angle)

To reconnect
Operation of the Door Controls:Lighted Door Control Button: Press to open or close the door.

Lighted Push Bar – Door Control Panel:Press the white square to open or close the door.

Press again to reverse the door during the closing cycle or to stop the door while it's opening.

Light Feature – Door Control Panel:Press the Light button to turn the opener light on or off. If you turn it on and then activate the opener, the light will remain on for 4- 1/2 minutes. Press again to turn it off sooner. The Light button will not control the opener lights when the door is in motion.

The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to 1-1/2 minutes.

See additional programming features, next page.

Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for a 3- 1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

Lock Feature – Door Control Panel:Designed to prevent operation of the door from portable remote controls. However, the door will open and close from the Door Control push bar, the Outside Keylock and the Keyless Entry Accessories.

To Activate: Press and hold the Lock button for

2 seconds. The push bar light will flash as long as the Lock feature is on.

To turn off: Press and hold the Lock button again for 2 seconds. The push bar light will stop flashing. The Lock feature will also turn off whenever the “Smart” button on the opener panel is activated.

28