Receiver & Remote Control Programming
NOTICE: To comply with FCC rules, adjustment or modification of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
“Security Plus”Your garage door opener receiver and remote control transmitter have been set at the factory to a matching code. The door will activate when you press the LARGE remote control push button.
Your "Security Plus" opener will operate with:
•several Security Plus remote controls (with yellow indicator lights) utilizing up to 8 functions. NOTE: Open/Close/Stop operation counts as 1 function.
•one Keyless Entry System (with Security Plus logo)
Follow the instructions below to program your opener to match any additional remotes you may purchase. See Accessories on page 34.
To Add a Remote Control1.Press and hold the selected remote control push button. See Figure 1.
WARNING
Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control(s) or remote control transmitter(s).
A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door clearly, it is free of obstructions, and is properly adjusted.
Security Plus Remote ControlYellow
Battery Indicator
Light 
Figure 1
Select a push butto
2.Press and release the "Smart" (learn) button on the right side panel of the opener. See Figure 2. The indicator light on the panel will begin to blink and the opener lights will flash once.
3.Release the remote push button.
Now the opener will operate when the remote control push button is pressed. Test by pressing the remote button to see that the door goes up and down.
Adding a remote can also be done from the door control, as follows:1.With the door closed, press and hold a remote push button.
2.Press and hold the Light button on the door control.
3.Press and hold the door control push bar.
4.After the opener lights flash, release all buttons. Test by pressing the remote push button.
To Erase All Remote Control CodesPress and hold the "Smart" button on the opener panel until the indicator light turns off (about 6 seconds). All transmitter codes are now erased. Then follow the steps above to
With Security Plus transmitters, a remote push button can be programmed to operate the opener lights without opening the door.
1.With the door closed, press and hold the remote button that you want to control the light.
2.Press and hold the Light button on the door control.
3.Press and hold the Lock button on the door control.
4.After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights should turn on or off but the door should not move.
Figure 2
Security PlusGarage Door Opener
|
|
|
|
| + |
1 | 2 |
|
|
| 3 |
| 8 | 1 | 8 |
| 1 |
| 7 | 3 | 7 | 5 | 3 |
|
| 5 |
| + | |
|
| Kg |
| Kg |
"Smart" (learn) Indicator
Button Light
Code programming instructions are also located on the opener panel.
Open/Close/Stop OperationYour Security Plus remote control can be programmed to operate one door using all 3 buttons: the large button will only open the door, the middle button will only close the door, and the third button will stop the door’s movement. You may set up this feature as follows:
1. | With the door closed, press and |
|
| hold the large remote push button. | Open |
2. | Press and hold the Lock button | Close |
Stop |
on the door control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by pressing the large (Open) button on the remote. The door should open. Press it again while the door is open and nothing should happen. Press the middle (Close) button and the door should close. Press the third (Stop) button while the door is moving and it should stop immediately.
Model 67LM Security Plus Keyless Entry Follow instructions on page 34 (Accessories).
29