Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 1000SDR 1/3 HP, 2000SDR 1/2 HP SECTIONAL Door or, ONE-PIECEDoor with Track Installation, ONE-PIECEDoor Without Track Installation

1 36

Download 36 pages, 995.22 Kb

Before you begin, survey your garage area to see whether any of the conditions below apply to your installation.

SECTIONAL Door orONE-PIECE Door with Track Installation

Horizontal and vertical reinforcement is needed for lightweight garage doors

(fiberglass, steel, aluminum, door with glass panels, etc.).

See page 20 for details.

Header Wall

FINISHED CEILING Support bracket & fastening hardware is required.

See page 13.

Extension Spring

OR	OR
Torsion Spring	One-Piece Door-Extension Spring
Torsion Spring
— —	Header
— —	Wall
—
Door Center
— — —	Track
	Track
— —	Door
— —
Safety
Reversing
Sensor
Floor must be level
across width of door

Safety Reversing Sensor

Access Door

ONE-PIECE Door Without Track Installation

FINISHED CEILING Support bracket

&fastening hardware is required. See page 13.

Header

Wall

Access Door

Safety

Reversing

Sensor

Gap between floor and bottom of

door must not exceed 1/4".

Safety Reversing Sensor

You may find it helpful to refer back to this page as you proceed with the installation of your opener.

5

Contents

Page Assembly section - pages 6 – Installation section - pages 8 – Adjustment section - pages 24 – Start by reviewing these important safety alert symbols: serious injury or death Test Your Door for Balance Sectional One-Piece Operation at other than 120V 60 Hz will cause opener malfunction and damage Hardware Supplied KEEP THE FOAM INTACT SECTIONAL Door or ONE-PIECEDoor with Track Installation ONE-PIECEDoor Without Track Installation Fasten the Rail To the Power Unit Install the Trolley IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of severe injury or death to persons: 1.READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS 5.Do not connect the opener to power source until instructed to do so Determine Header Bracket Location ONE-PIECEDoor Without Track One-piecedoor without track jamb hardware pivot hardware EXAMPLE Install the Header Bracket Attach the Rail to the Header Bracket IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR must Install the Safety Reversing Sensor (Receiving and Sending Eyes) Install the Safety Reversing Sensor Position the Opener Hang the Opener Install the Door Control and Connect all Wiring Electrical Requirements Complete Safety Reversing Sensor Installation Install the Lights and Lens Attach the Manual Release Rope and Handle Fasten Door Bracket All ONE-PIECEDoor Installation Procedure Connect Door Arm to Trolley All ONE-PIECEDoors Assemble the Door Arm: Adjustment Procedures for One-PieceDoors Open Door Adjustment: Decrease UP Travel Limit Adjust the UP and DOWN Limits Adjust the Force Test The Protector System ® Test the Safety Reverse System 1.READ AND FOLLOW ALL INSTRUCTIONS KEEP GARAGE DOORS PROPERLY BALANCED. See page Force and Limit Adjustment Controls The Remote Control Transmitter The Transmitter Battery Activate the opener with any of the following: The Remote Control Transmitter The Door Control •The Outside Keylock or Keyless Entry Lockout position “Security Plus” NOTE: To Add a Remote Control Security Plus Remote Control Adding a remote can also be done from the door control, as follows: Situation Probable Cause & Solution The opener doesn't operate from either the door control or the remote control: Opener operates from the remote control, but not from the door control: The door operates from the door control, but not from the remote control: (continued) Rail Assembly Parts Installation Parts KEY PART NO Power Unit Parts Model 1702LM Outside Quick Release Model 971LM Remote Control Model 59LM Garage Door Manual Release Rope & Handle Opener Terminals Operational Noise Receiver & Remote Controls