|
|
|
|
|
|
| Technical Information | |
|
|
|
|
|
|
| ||
Troubleshooting Guide |
|
|
|
| ||||
| Symptom |
| Cause(s) |
| Action(s) | |||
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| General low light intensity |
| • | Dirty lens assembly |
| • | Clean the fixture regularly | |
|
| • | Misaligned lens assembly |
| • | Install lens assembly properly | ||
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| A single LED (Red, |
| • | Faulty LED |
| • | Replace the LED board | |
| Green, Blue or White) |
| • | Faulty LED board |
| • | Replace the LED board |
|
| does not illuminate |
|
| |||||
| A group of LEDs (Red, |
| • | Faulty LED |
| • | Replace the LED board | |
|
|
| Faulty LED board |
|
| Replace the LED board | ||
| Green, Blue or White) |
| • |
| • | |||
| does not illuminate |
| • | Faulty LED driver |
| • Replace the LED driver board | ||
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| None of the LEDs are |
| • | Faulty LED PCB |
| • | Replace the LED board | |
|
| • | Faulty LED Driver PCB |
| • Replace the LED driver board | |||
| illuminating |
|
| |||||
|
| • | Faulty main PCB |
| • Replace the Display / Main board | |||
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| Breaker/Fuse keeps |
| • | Excessive circuit load |
| • | Check total load placed on the electrical circuit | |
| blowing |
| • | Short circuit along the power wires |
| • Check for a short in the electrical wiring | ||
|
|
|
| |||||
|
|
|
|
|
|
|
| |
|
|
| • | No power |
| • Check for power on power outlet | ||
| Fixture does not power up |
| • | Loose or damaged power cord |
| • | Check power cord | |
|
|
| • | Blown internal fuse |
| • | Replace internal fuse | |
|
|
| • | Faulty internal power supply |
| • | Replace internal power supply | |
|
|
|
|
|
|
|
| |
|
|
| • | Wrong DMX addressing |
| • Check Control Panel and unit addressing | ||
|
|
| • | Damaged DMX cables |
| • | Check DMX cables | |
| Fixture does not respond |
| • | Wrong polarity on the controller |
| • | Check polarity switch settings on the controller | |
| to DMX |
| • | Loose DMX cables |
| • | Check cable connections | |
|
|
|
| |||||
|
|
| • | Faulty DMX interface |
| • | Replace Main PCB | |
|
|
| • | Faulty Main PCB |
| • | Replace Main PCB | |
|
|
|
|
|
|
|
|
|
|
|
| • | Non DMX cables |
| • | Use only DMX compatible cables | |
|
|
| • | Bouncing signals |
| • | Install terminator as suggested | |
|
|
| • Long cable / low level signal |
| • | Install an optically coupled DMX splitter right | ||
| DMX signal problems |
|
|
|
|
| after fixture with strong signal | |
|
|
|
|
|
|
|
| |
|
|
| • | Too many fixtures |
| • | Install an optically coupled DMX splitter after | |
|
|
|
|
|
|
| unit #32 | |
|
|
| • | Interference from AC wires |
| • Keep DMX cables separated from power cables | ||
|
|
|
|
|
|
| or black lights | |
|
|
|
|
|
|
|
|
|
If you still experience technical problems after trying the above solutions, contact CHAUVET® Technical Support.
COLORado™ 1 IP User Manual Rev. 01c |
