Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 71642 manual Configure Access Point Detail, AP Detail

Models: 71642

1 32

Download 32 pages 63.45 Kb

Page 21

Image 21

Configure Access Point Detail

Complete these steps:

1.Click Detail.

2.Configure the AP Name.

3.Ensure that the access point is configured for DHCP.

4.Ensure that Admin Status is Enabled.

5.AP Mod should be set to local.

6.Enter the location of the access point.

7.Enter the controller name that the access point belongs to. The controller name can be found on the Monitor page.

8.Click Apply.

Figure 13AP Detail

Page 21

Image 21

Cisco Systems 71642 manual Configure Access Point Detail, AP Detail

Contents

Wireless Network Infrastructure Vocera Communications Server Capacity The Vocera SolutionSwitch Recommendations Deployments and Configuration Wireless Network Infrastructure ConfigurationNetPro Discussion Forums − Featured Conversations Related Information Audio ProblemsIntroduction PrerequisitesVocera Badge Overview The Vocera SolutionVocera Call Capacity Considerations Vocera Communications Server CapacityArchitecture Overview Voceras Infrastructure PlanningMulticast in an LWAPP Deployment Unicast−Multicast Delivery MethodFigure 2LWAPP Multicast−Unicast Figure 3LWAPP Multicast−Multicast Multicast−Multicast Delivery MethodEnable IP Multicast Routing Router and Switch Multicast ConfigurationEnable PIM on an Interface Routerconfig#ip multicast−routingDisable Switch VLAN IGMP Snooping Deployment ScenariosMulticast Enhancements in Version 4.0.206.0 and Later Single Controller Deployment Figure 5Single Controller in Multicast−Multicast ModeMultiple Controller Layer 2 Deployment Multiple Controller Layer 3 DeploymentFigure 6Multiple Controller Layer 2 Deployment Recommendations for Multi−Floor Buildings, Hospitals, and Warehouses VoWLAN Deployments Ciscos ReccommendationsFigure 7Multiple Controller Layer 3 Deployment Construction Methods and MaterialsLevels of Inventory InventoryActivity Levels Multi−Floor BuildingsSecurity Mechanisms Supported LEAP ConsiderationsWarehouses Number of 802.11b Devices per Access Point Wireless Network InfrastructureNumber of Active Calls per Access Point Voice, Data and Vocera VLANsDeployments and Configuration Switch RecommendationsBadge Configuration ∙ Subnet Roaming is disabledTune AutoRF for Your Environment ∙ What do I do if my transmit power is too hot? ∙ How do I know if the tranmit power is too hot or too cold?∙ What do I do if my transmit power is too cold? ∙ Isolated Behavior4. Disable Aggressive Load Balancing Wireless Network Infrastructure ConfigurationFigure 9General WLC Configuration Create InterfacesFigure 11802.11b/g Configuration Wireless−Specific ConfigurationCreate the Vocera Voice Interface Figure 10List of WLC InterfacesFigure 12WLAN Configuration WLAN ConfigurationFigure 13AP Detail Configure Access Point DetailConfigure the 802.11b/g Radio 7. Choose Wireless Access Points 802.11b/g Radios Wireless IP Telephony VerificationAssociation, Authentication, and Registration Badge Loses Voice Quality while Roaming Common Roaming IssuesRegistration and Authentication Problems Audio ProblemsOne−sided Audio Choppy or Robotic AudioAP and Antenna Placement Figure 17Improper Placement of Antennas Near an I−BeamAppendix A Figure 21Cisco AP1200 Mounted to a Ceiling Figure 20Signal Reflection Caused by a WallFigure 22Cisco Aironet 5959 Antenna Mounted to a Ceiling Figure 23Cisco AP1200 Mounted to a WallFigure 24Cisco Aironet 2012 Antenna Mounted to a Wall Interference and Multipath Distortion Figure 25Signal−to−Noise Ratio SNRNetPro Discussion Forums − Featured Conversations Signal AttenuationSignal Attenuation Caused By Various Types of Objects ∙ Solution Reference Network Design ∙ Deploying Cisco 440X Series Wireless LAN Controllers∙ Vocera Communications System Specifications Related Information

Configure Access Point Detail

Figure 13￿AP Detail

Figure 13AP Detail