Cisco Systems 7301 8

29

8 After Installation

Follow the instructions in this section to replace options after installation. Use the installation and removal information in this

section to power off the router, remove the cover, replace the option, replace the cover, and power on the router.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the

power at the circuit breaker on DC units.

Statement 12

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the

backplane with your hand or any metal tool, or you could shock yourself.

Statement 94

Power Off the Cisco 7301 Router

Step 1 Power off the router by placing the power switch in the OFF (|) position.

Step 2 Remove any cables from the Cisco 7301 router, including the power cables. For AC power supplies, unplug the AC

power cord from the power outlet. For DC power supplies, to ensure that all power is off, locate the circuit breaker on

the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle

of the circuit breaker in the OFF position.

Note After powering off the router, wait a minimum of 30 seconds before powering it on again.

Replace the CompactFlash Disk

Figure 19 Inserting and Removing the CompactFlash Disk

To remove the CompactFlash Disk, press the ejector button, grasp the CompactFlash Disk and pull it from the slot (2).

1Insert the CompactFlash Disk 2Press the ejector button and remove the CompactFlash

Disk

80270

21

ALARM

ONSOLE

COMP

ACT

FLASHSTATUS

100-240V

, 2A, 50/60 Hz

24V

=

9A, 48 - 60V

=

5A

BA

ALARM

ONSOLE

COMP

ACT

FLASHSTA

TUS

100-240V

, 2A, 50/60 Hz

24V

=

9A, 48 - 60V

=

5A

BA

Contents

Main 1 Documentation Survey Obtaining Documentation, Obtaining Support, and Security Guidelines Document Revision History 2 Site Preparation and Unpacking Tools and Parts Two rack-mount brackets and one cable-management bracket Prepare for Workbench or Tabletop Installation Prepare for Rack-Mount Installation 3 357 468 15 910 Install the SFP Gigabit Interface Converter Module 1 2 3 Figure 3 Inserting a SFP GBIC Module into a SFP GBIC Port Figure 4 Attaching the Rack-Mount Brackets to the Front of the Chassis 4 This section provides information for rack-mounting the router. Attach the Rack-Mount BracketsChassis Front-Mounted 1 SFP GBIC port 2 1 Rack-mount bracket 2 Attach the Rack-Mount BracketsChassis Rear-Mounted 1 Rack-mount bracket 2 Attach the Cable-Management Bracket Figure 6 Attaching the Cable-Management Bracket BA CISCO 7301 Four-Post Rack Installation Two-Post Rack Installation 1 Two-post rack 3 2 Chassis Ground Connection Installation 1 Chassis ground connector 3 2 Grounding lug 4 5 4 5 Console and Auxiliary Port Cable Connections Gigabit Ethernet SFP GBIC and RJ-45 Connections 1Auxiliary port 4Cable to modem or DCE 2 Console port 5 3 SFP GBIC Cabling and Connection Equipment 1 3 1 To external 1000BASEX network 4 2 1 duplex connector (TX and RX) 5 3 SFP GBIC module 6 46 Attach the Mode-Conditioning Patch Cord / / / / Port Adapter Cable Connections / / Alarm Port Connection Figure 14 Connecting the Alarm Port Cable BA CISCO 7301 ALARM 6 Connect Power to the Router 1 AC power receptacle 2 Connect AC-Input Power Connect DC-Input Power 1 DC plug 4 2 Lead 5 3 Observe the System Startup and Perform a Basic Configuration Start the Router 7 Performing a Basic Configuration Using the Setup Facility Configure Global Parameters Page Configure an Auxiliary Port to Receive Console Port Messages Configure the Native Gigabit Ethernet Interfaces Change the Media Type of the Native Gigabit Ethernet SFP GBIC or RJ-45 Ports Configure the Interface Transmission and Speed Modes Debug Reset the Interface Clear Counters Configure Port Adapter Interfaces interfaces that might be used. Configure ATM Interfaces Configure Fast Ethernet Interfaces Configure Synchronous Serial Interfaces Enabling the Second Processor Save the Running Configuration to NVRAM Check the Running Configuration Settings View Your System Configuration Perform Complex Configurations Replace or Recover a Lost Password 8 Power Off the Cisco 7301 Router Replace the CompactFlash Disk 1 Insert the CompactFlash Disk 2 Replace the Port Adapter or Service Adapter 1 Port adapter latch 3 2 Port adapter partially removed 4 For specific port adapter information, see the appropriate port adapter documentation. Replace the SODIMMs Power Off the Router and Remove the Cover 1 1 1 Remove and Install the SODIMMs 1 22 1SODIMM 2SODIMM spring latches Replace the Cover and Power On the Router 1 Insert cover under router lip 2 9 Cisco Technical Support Website Submitting a Service Request Definitions of Service Request Severity