Cisco Systems 7301 Replace the Port Adapter or Service Adapter

30

Insert the CompactFlash Disk into the CompactFlash Disk slot with the label with the vendor name and memory size facing up.

The CompactFlash Disk protrudes when completely inserted.

Note Only the CompactFlash Disk is supported in a Cisco 7301 router. Other types of Flash Disks are not supported.

•The larger the CompactFlash Disk size, the longer the system boot time.

•The CompactFlash Disk supports online insertion and removal (OIR).

•Use the CompactFlash Disk to store your configuration files and Cisco IOS software image. The Cisco 7301 router has no

onboard Flash memory.

For more information on CompactFlash Disk, see Appendix B, “Using the CompactFlash Disk,” in the Cisco 7301 Installation

and Configuration Guide.

Replace the Port Adapter or Service Adapter

The port adapter or service adapter ships installed. These instructions are provided for future use. Cabling information is

included with the specific port adapter documentation.

Figure 20 Removing and Installing the Port Adapter

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the

backplane with your hand or any metal tool, or you could shock yourself.

Statement 94

.

Note Before removing any port adapter, gracefully shut down the interface so that there is no traffic running through the port

adapter when it is removed. Removing a port adapter while traffic is flowing through the ports can cause system

disruption.

Step 1 Attach an ESD wrist strap between you and an unpainted chassis surface. For wrist straps with a banana jack, insert

the banana jack in its grounding hole located on the front of the chassis, near the STATUS LED and power switch.

1Port adapter latch 3Port adapter slot guide

2Port adapter partially removed 4Ground for ESD wrist strap banana jack

80268

ALARM

RJ45 ENLINK

TXRX

GBIC

GIGABIT ETHERNET 0/2

RJ45 ENLINK

TXRX

GBIC

GIGABIT ETHERNET 0/0

RJ45 ENLINK

TXRX

GBIC

GIGABIT ETHERNET 0/1

CISCO 7301

SLOT 1

CONSOLE

AUX

COMP

ACT

FLASHST

A

TUS

100-240V, 2A, 50/60 Hz

24V

=

9A, 48 - 60V

=

5A

1

ENABLED

RX CELLS

RX CARRIER

RX ALARM

ATM

2

4

3

BA

Contents

Main 1 Documentation Survey Obtaining Documentation, Obtaining Support, and Security Guidelines Document Revision History 2 Site Preparation and Unpacking Tools and Parts Two rack-mount brackets and one cable-management bracket Prepare for Workbench or Tabletop Installation Prepare for Rack-Mount Installation 3 357 468 15 910 Install the SFP Gigabit Interface Converter Module 1 2 3 Figure 3 Inserting a SFP GBIC Module into a SFP GBIC Port Figure 4 Attaching the Rack-Mount Brackets to the Front of the Chassis 4 This section provides information for rack-mounting the router. Attach the Rack-Mount BracketsChassis Front-Mounted 1 SFP GBIC port 2 1 Rack-mount bracket 2 Attach the Rack-Mount BracketsChassis Rear-Mounted 1 Rack-mount bracket 2 Attach the Cable-Management Bracket Figure 6 Attaching the Cable-Management Bracket BA CISCO 7301 Four-Post Rack Installation Two-Post Rack Installation 1 Two-post rack 3 2 Chassis Ground Connection Installation 1 Chassis ground connector 3 2 Grounding lug 4 5 4 5 Console and Auxiliary Port Cable Connections Gigabit Ethernet SFP GBIC and RJ-45 Connections 1Auxiliary port 4Cable to modem or DCE 2 Console port 5 3 SFP GBIC Cabling and Connection Equipment 1 3 1 To external 1000BASEX network 4 2 1 duplex connector (TX and RX) 5 3 SFP GBIC module 6 46 Attach the Mode-Conditioning Patch Cord / / / / Port Adapter Cable Connections / / Alarm Port Connection Figure 14 Connecting the Alarm Port Cable BA CISCO 7301 ALARM 6 Connect Power to the Router 1 AC power receptacle 2 Connect AC-Input Power Connect DC-Input Power 1 DC plug 4 2 Lead 5 3 Observe the System Startup and Perform a Basic Configuration Start the Router 7 Performing a Basic Configuration Using the Setup Facility Configure Global Parameters Page Configure an Auxiliary Port to Receive Console Port Messages Configure the Native Gigabit Ethernet Interfaces Change the Media Type of the Native Gigabit Ethernet SFP GBIC or RJ-45 Ports Configure the Interface Transmission and Speed Modes Debug Reset the Interface Clear Counters Configure Port Adapter Interfaces interfaces that might be used. Configure ATM Interfaces Configure Fast Ethernet Interfaces Configure Synchronous Serial Interfaces Enabling the Second Processor Save the Running Configuration to NVRAM Check the Running Configuration Settings View Your System Configuration Perform Complex Configurations Replace or Recover a Lost Password 8 Power Off the Cisco 7301 Router Replace the CompactFlash Disk 1 Insert the CompactFlash Disk 2 Replace the Port Adapter or Service Adapter 1 Port adapter latch 3 2 Port adapter partially removed 4 For specific port adapter information, see the appropriate port adapter documentation. Replace the SODIMMs Power Off the Router and Remove the Cover 1 1 1 Remove and Install the SODIMMs 1 22 1SODIMM 2SODIMM spring latches Replace the Cover and Power On the Router 1 Insert cover under router lip 2 9 Cisco Technical Support Website Submitting a Service Request Definitions of Service Request Severity