Manuals
/
Brands
/
Computer Equipment
/
Network Router
/
Cisco Systems
/
Computer Equipment
/
Network Router
Cisco Systems
7301 quick start
1
1
34
34
Download
34 pages, 1.22 Mb
Q
UICK
S
TART
G
UIDE
Cisco 7301 Router
1
Documentation and Resources
2
Prepare for Installation
3
Install External Options
4
Rack-Mount the Router
5
Connect the Router to the Network
6
Start the System
7
Configure the Router
8
After Installation
9
Obtaining Technical Assistance
Contents
Main
1
Documentation Survey
Obtaining Documentation, Obtaining Support, and Security Guidelines
Document Revision History
2
Site Preparation and Unpacking
Tools and Parts
Two rack-mount brackets and one cable-management bracket
Prepare for Workbench or Tabletop Installation
Prepare for Rack-Mount Installation
3
357
468 15
910
Install the SFP Gigabit Interface Converter Module
1 2 3
Figure 3 Inserting a SFP GBIC Module into a SFP GBIC Port
Figure 4 Attaching the Rack-Mount Brackets to the Front of the Chassis
4
This section provides information for rack-mounting the router.
Attach the Rack-Mount BracketsChassis Front-Mounted
1 SFP GBIC port 2
1 Rack-mount bracket 2
Attach the Rack-Mount BracketsChassis Rear-Mounted
1 Rack-mount bracket 2
Attach the Cable-Management Bracket
Figure 6 Attaching the Cable-Management Bracket
BA
CISCO 7301
Four-Post Rack Installation
Two-Post Rack Installation
1 Two-post rack 3 2
Chassis Ground Connection Installation
1 Chassis ground connector 3 2 Grounding lug 4
5
4 5
Console and Auxiliary Port Cable Connections
Gigabit Ethernet SFP GBIC and RJ-45 Connections
1Auxiliary port 4Cable to modem or DCE 2 Console port 5 3
SFP GBIC Cabling and Connection Equipment
1 3
1 To external 1000BASEX network 4 2 1 duplex connector (TX and RX) 5 3 SFP GBIC module 6
46
Attach the Mode-Conditioning Patch Cord
/ / / /
Port Adapter Cable Connections
/ /
Alarm Port Connection
Figure 14 Connecting the Alarm Port Cable
BA
CISCO 7301
ALARM
6
Connect Power to the Router
1 AC power receptacle 2
Connect AC-Input Power
Connect DC-Input Power
1 DC plug 4 2 Lead 5 3
Observe the System Startup and Perform a Basic Configuration
Start the Router
7
Performing a Basic Configuration Using the Setup Facility
Configure Global Parameters
Page
Configure an Auxiliary Port to Receive Console Port Messages
Configure the Native Gigabit Ethernet Interfaces
Change the Media Type of the Native Gigabit Ethernet SFP GBIC or RJ-45 Ports
Configure the Interface Transmission and Speed Modes
Debug
Reset the Interface
Clear Counters
Configure Port Adapter Interfaces
interfaces that might be used.
Configure ATM Interfaces
Configure Fast Ethernet Interfaces
Configure Synchronous Serial Interfaces
Enabling the Second Processor
Save the Running Configuration to NVRAM
Check the Running Configuration Settings
View Your System Configuration
Perform Complex Configurations
Replace or Recover a Lost Password
8
Power Off the Cisco 7301 Router
Replace the CompactFlash Disk
1 Insert the CompactFlash Disk 2
Replace the Port Adapter or Service Adapter
1 Port adapter latch 3 2 Port adapter partially removed 4
For specific port adapter information, see the appropriate port adapter documentation.
Replace the SODIMMs
Power Off the Router and Remove the Cover
1 1
1
Remove and Install the SODIMMs
1 22
1SODIMM 2SODIMM spring latches
Replace the Cover and Power On the Router
1 Insert cover under router lip 2
9
Cisco Technical Support Website
Submitting a Service Request
Definitions of Service Request Severity