
2: Connect the Router to a Hub (Optional)
See the “3: Connect a Digital Subscriber Line” section on page 5 to complete the next step.
2: Connect the Router to a Hub (Optional)
If you have PCs connected to a hub, follow the steps shown in Figure 2 on page 4 to connect the router to a hub. Figure 2 shows portions of two router back panels. Refer to the back panel that is similar to the back panel of the router that you are installing.
Figure 2 |
| Connecting the Router to a Hub |
|
|
1. Set TO HUB/TO PC | 1. Set TO HUB/TO PC | |||
| button. | button. | ||
|
| Cisco 827, Cisco |
|
|
|
|
|
| |
|
| or SOHO 77 router |
|
|
|
|
|
|
|
Cisco 827H, Cisco 828, SOHO 77H, or SOHO 78 router
TO HUB | ETHERNET | CONS | OLE |
| Model | Cisco |
|
|
| |
TO PC |
|
| ADSL |
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||
| 1 |
|
|
|
|
|
|
| PHONE | |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 4 | 3 | 2 |
|
|
|
|
|
|
|
|
| 1 | ||
|
|
|
|
|
|
|
|
|
2.Connect yellow cable to ETHERNET port on router.
TO HUB | ETHERNET | 10BASE T | Model | Cisco 828 | |
TO | PC | ||||
|
|
| |||
|
|
|
| CONSOLE | |
|
| 4 |
|
| G.SHDSL |
|
|
|
|
| |
|
| 3 | 2 |
|
|
|
|
| 1 |
| |
|
|
|
|
|
2.Connect yellow cable to ETHERNET port on router.
Cisco 1528 Micro Hub 10/100
|
|
|
|
| 1X | 2X | ETHER |
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
SPEED |
|
|
|
|
|
|
| NET 3X |
| 4X |
|
LED |
|
|
|
|
|
|
|
|
| ||
100BaseTX | 1 | 2 |
|
|
|
|
|
|
|
| |
SOLID | 3 | 4 |
|
|
|
|
|
| |||
10BaseT |
|
|
|
|
|
|
|
| |||
BLINK | 5 | 6 | 7 | 8 |
|
|
|
|
|
| |
|
|
|
|
|
|
| |||||
|
|
|
|
| 5X |
| 6X | 7X |
|
|
|
|
|
|
|
|
|
| 8X |
|
| ||
|
|
|
|
|
|
|
| MDI |
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
3.Connect other end of cable
to hub. | 4. If applicable, check setting |
| of hub equivalent of router |
| TO HUB/TO PC button. |
74082
1 | Set TO HUB/TO PC button for Cisco 827, | 4 | Cisco 1528 Micro Hub 10/100 |
| SOHO 77 router. |
|
|
|
|
|
|
2 | Set TO HUB/TO PC button for Cisco 827H, 828, | 5 | Connect other end of cable to hub. |
| SOHO 77H or SOHO 78 router. |
|
|
|
|
|
|
3 | Connect yellow cable to Ethernet port on router. | 6 | If applicable, check settings of hub equivalent of router |
|
|
| TO HUB/TO PC button. |
|
|
|
|
Verify that the TO HUB/TO PC switch on the left side of the back panel has been set to the TO HUB position (in). If the button is out, press it to set it to the in position. You will know that the position is correct if the LED for this port on the front of the router lights after the router and the PCs have been turned on.
Cisco 820 Series and SOHO Series Routers Cabling and Setup Quick Start Guide
4 |
| |
|