Cisco Systems manual 27

Cisco TelePresence PrecisionHD Camera					PrecisionHD Camera User guide
Contents	Introduction	The physical interface	Connecting the camera	Video output formats	Daisy chaning	Appendices

The VISCA™/RS–232 control protocol, cont...

NOTE: Some VISCA™ commands do not apply to the PrecisionHD 1080p4x/4xS2 cameras.

Camera commands, continued...

Command		Command Packet	Comments
Mirror_On	8x	01 04 61 02 ff	Sony calls this CAM_LR_Reverse.
Mirror_Off	8x	01 04 61 03 ff	RR (FT/AT mirror command).
			The “xConfiguration Cameras
			Camera [1..n] Mirror: Auto”
			(supported by the Codec C-series)
			do not apply to the PrecisionHD
			1080p 4x.
Flip_On	8x	01 04 66 02 ff	Sony calls this CAM_ImgFlip.
Flip_Off	8x	01 04 66 03 ff	The “xConfiguration Cameras
			Camera [1..n] Flip: Auto” (supported
			by the Codec C-series) do not
			apply to the PrecisionHD 1080p 4x.
Gamma_Auto	8x	01 04 51 02 ff	Gamma mode. Default uses
Gamma_Manual	8x	01 04 51 03 ff	gamma table 4.
Gamma_Direct	8x	01 04 52 0p 0q 0r	pqrs: Gamma table to use in
	0s ff		manual mode. Range 0-7.
MM_Detect_On	8x	01 50 30 01 ff	Turn on the Motor Moved
			Detection (camera recalibrates if
			touched)
MM_Detect_Off	8x	01 50 30 00 ff	Turn off the Motor Moved
			Detection (camera does not
			recalibrate if touched)
Call_LED_On	8x	01 33 01 01 ff	Refers to orange LED on top of
Call_LED_Off	8x	01 33 01 00 ff	camera. Will always be off at
			startup.
Call_LED_Blink	8x	01 33 01 02 ff
Power_LED_On	8x	01 33 02 01 ff	Green power LED. If switched to
Power_LED_Off	8x	01 33 02 00 ff	off and stored to startup profile, it
			will always be off.

Command	Command Packet	Comments
IR_Output_On	8x 01 06 08 02 ff	See IR push message.
IR_Output_Off	8x 01 06 08 03 ff
IR_CameraControl_	8x 01 06 09 02 ff	Lets up/down/left/right/zoom+/-
On		on the IR remote control the
IR_CameraControl_	8x 01 06 09 03 ff	camera directly. Those keycodes
		will be sent to the controller if IR
Off
		Output is on.

PTZF - movement commands

Command		Command Packet		Comments
Zoom_Stop	8x	01 04 07 00 ff
Zoom_Tele	8x	01 04 07 2p ff		p = speed parameter,
Zoom_Wide	8x	01 04 07 3p ff		a (low) to b (high)
Zoom_Direct	8x	01 04 47 0p 0q 0r		pqrs: zoom position
	0s ff
ZoomFocus_Direct	8x	01 04 47 0p 0q 0r		pqrs: zoom position
	0s			tuvw: focus position
	0t 0u 0v 0w ff
Focus_Stop	8x	01 04 08	00 ff
Focus_Far	8x	01 04 08	2p ff	p = speed parameter,
Focus_Near	8x	01 04 08	3p ff	a (low) to b (high)
Focus_Direct	8x	01 04 48	0p 0q 0r	pqrs: focus position
	0s ff

*Do not apply to PrecisionHD 4x/4xS2 cameras

D14640.09 PrecisionHD 1080p-720p Camera User Guide, June 2012.	27	www.cisco.com
© 2010-2012 Cisco Systems, Inc. All rights reserved.